background image

16

ENG 

When cleaning and doing maintenance,
make sure the safety instructions set out
on page 14 are complied with. 

• If your kitchen hood is made from stainless

steel, use this material's specially designed
cleaners mentioned in the product
suppliers' instructions.

• Never use metallic scourers, nor abrasive

or corrosive products.

• Dry the kitchen hood using a cloth that

does not produce fluff.

Extract the filters  from their housings using
the handles specially designed for this
purpose.

The metal filters can be cleaned by soaking
them in hot water with neutral detergent until
the fat dissolves and then rinsing them under

the tap or using products specially designed
for fats. They can also be washed in a
dishwasher. In this case, it is advisable to
stack them vertically to avoid food residue
sticking to them.

Cleaning in a dishwasher with aggressive
detergents or polish may damage the metallic
surface (blackening it), although this will not
affect its fat retention capacity.

Once clean, leave them to dry off and then fit
them onto the kitchen hood.

Proceed as follows:

•  Remove the metal filters.

•  Dismount the support (B) by loosening the

screws (A).

• Change the broken/burnt out lamp.

Maximum lamp power is 20 W (G-4).

•  Mount the support again (B).

•  Fit the metal filters.

Cleaning the metal filters

Cleaning and maintenance

_________________________________________________________

Problem solving

Proceed with the following checks before calling Technical Services:

Solution

Change the lamps.

Tighten the lamps.

Change or clean the active charcoal
and/or metal filters, as the case
may be.

Remove the obstruction.

Connect feed cable to the
network.

Check that the network has
current.

The lamps do not light up.

The lamps are burnt out.

The lamps are slack.

The kitchen hood does not 
extract sufficiently or vibrates.

The extractor fan does not work.

Problem

Possible cause

Filters are saturated with fat.

Obstruction in the air exit conduct.

The extractor fan feed cable is not
connected to the network.

There is no current in the network.

Changing lights

Cleaning the body of the kitchen hood

Manual_DX.qxd  12/01/2005  17:03  Page 16

Содержание DX series








Отзывы: