manualshive.com logo in svg

Tecumseh ECV100, Руководство пользователя

Поделиться
Скачать
Tecumseh ECV100 Скачать руководство пользователя страница 28

24

55

56

Inlet Fuel Fitting

To remove a leaking or damaged fuel inlet fitting, use a
1/4"(6 mm) bolt, 1/4" (6 mm) nut and 1/4" (6 mm) washer,
along with a 1/2" (12 mm) nut. Use a pliers or vise to
remove the plastic part of the inlet fitting. Tap the inside
of the remaining metal portion of the fitting using a
1/4"- 20  (6 mm) tap. Place a 1/2" (12 mm) nut over the
fuel fitting (it may be necessary to guide one side of
the nut to seat it squarely to the carburetor). Next thread
the 1/4" (6 mm) nut on the bolt until it contacts the shank,
add the washer, and thread the bolt into the fitting until
snug. Tighten the 1/4"- 20 (6 mm) nut until the fitting is
removed. (diag. 56)

Primer Bulb

To install, start the retainer and bulb into the casting with
the retainer tabs pointed out. Firmly push the bulb and
retainer into position using a 3/4'’ (19.05 mm) deep well
socket (diag. 55).

Final Checks

Before reinstalling a newly overhauled carburetor, pre-set
the main mixture adjustment screw, the idle mixture
adjustment screw and the idle speed adjustment screw.
See “Pre-sets and Adjustments” in this chapter.

STANDARD SERVICE CARBURETORS

Tecumseh supplies some replacement carburetors on which parts from the old carburetors can be reused or new parts
added. This Standard Service Carburetor helps to reduce dealer inventories.

Standard Service Carburetors are built in both float and diaphragm versions.

The parts from the original carburetor that are necessary to make a standard service carburetor are: choke shaft, shutter
and spring, throttle lever and spring, fuel fitting, idle adjustment screw and spring. If any or all of these old parts are worn
or damaged, replace each part with a new service part to assure proper function and prevent engine damage. Use the
diagrams on the next page as a guide to facilitate the correct installation of parts (diag. 57 & 58).

Fuel Fitting

NOTE: MOST SERVICE CARBURETORS ARE MARKED “SVC CARB NF” IN THE PRICE LIST. THIS MEANS THAT
THE CARBURETOR COMES WITH NO FUEL FITTING.

Use the parts manual to obtain the same fuel inlet fitting that was installed in the original carburetor. Install the fuel fitting
in the new carburetor body in the same position as on the original carburetor. Support the carburetor body with a wood
block to avoid damage to other parts. Use a bench vise or press to install the fitting squarely. Press it in until it bottoms
out.

NOTE: PRESS FUEL FITTING IN SQUARELY USING CAUTION SO THAT THE CARBURETOR BODY IS NOT
DAMAGED.

Choke Shaft

NOTE: Never reuse choke or throttle shutter screws, always replace with new Tecumseh service screws.

Remove the choke shutter screw from the original carburetor and remove the choke shaft. Observe the position of the
ends of the choke return spring if one is present. Also observe the position of the cut-out and/or holes in choke shutter.
Some chokes turn clockwise and some turn counterclockwise, note the position of the choke shaft prior to removal from
the old carburetor.

If a choke stop spring is present on the new carburetor and is not used on the old carburetor, cut it off with a side cutter
or pull it out using a pliers.

Test the action of choke shaft to make sure it moves freely and easily and does not bind in either open or closed position.
If binding occurs, loosen the shutter screw; reposition the shutter and tighten the screw.

Содержание ECV100




























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды