Tecnet TP-8000 SERIES Скачать руководство пользователя страница 23

Страница: 23 / 30

TP-8000 Programming Manual

1.13.5 Volume Level

This controls volume level at radio because volume switch has been replaced with GPA antenna. Use pull
down menu to decide volume level.

☞

Volume Level is set for the radio that has the GPS device.

1.13.6 Appoint Time

SYNC Enable Not-selected: GPS information is transmitted when time passes over setup value designated
in Appoint Time.

SYNC Enable Selected: When time passes over setup value designated in Appoint Time, the GPS
information is transmitted incrementally by time slot as defined in Time Slot Number (for multiple units in
operation).

1.13.7 Country Hour

Input the number of hours that the radio will operate in with the difference from General Mountain Time
(GMT).

☞

Value of negative number shows negative number value of 24+ (ex: If it is -9, it shows 24-9

= 15 hours)

1.13.8 TimeSlot NO

If the SYNC Enable box is checked, GPS information is transmitted at the time slot that is defined by the
value located in the Appoint time section.

(Example: If Appoint time is 30 seconds, a maximum total of 15 (0~14) radios can be utilized).

1.13.9 GPS Frequency

Frequency is same as channel designated to transmit GPS information via input wireless frequency.

GPS information is transmitted and received through this frequency.

1.13.10 ID Kind

Selects ID to transmit via 5- Tone or DTMF.

Содержание TP-8000 SERIES































Результаты поиска

Содержание TP-8000 SERIES

Отзывы:

Похожие инструкции для TP-8000 SERIES

Бренды по названию

Популярные бренды

Tecnet TP-8000 SERIES, Руководство по программированию ПК

Результаты поиска

Содержание TP-8000 SERIES

Отзывы:

Похожие инструкции для TP-8000 SERIES

Бренды по названию

Популярные бренды