TechVision PS32E8N2 Скачать руководство пользователя страница 83

Страница: 83 / 121

Alarm Management

DVR User Manual

interface as shown below.

②

Enable or disable “Alarm-out”, “Buzzer”, “Pop-up Message Box” and “E-mail”. The

exception handling settings are similar to that of the sensor alarm (see 9.1 Sensor Alarm for
details).

③

Click “Apply” to save the settings.

9.5 Alarm Event Notification

9.5.1 Alarm-out

①

Click Start



Settings



Alarm



Event Notification to go to the following interface.

②

Set the delay time and the schedule of each alarm-out. You can click “Edit Schedules” to

edit the schedules (see 7.3.1 Add Schedule for details).

③

Click “Apply” to save the settings. You can click “Test” to test the alarm output.

9.5.2 E-mail

Click Start



Settings



Alarm



Event Notification



E-mail to go to the e-mail configuration

Содержание PS32E8N2


























































































































Результаты поиска

Содержание PS32E8N2

Отзывы:

Похожие инструкции для PS32E8N2

Бренды по названию

Популярные бренды

TechVision PS32E8N2, Руководство пользователя

Результаты поиска

Содержание PS32E8N2

Отзывы:

Похожие инструкции для PS32E8N2

Бренды по названию

Популярные бренды