5
SNOOZE FUNCTION
PRESS “SNOOZE” BUTTON ON THE REMOTE CONTROL WHEN ALARM IN ACTIVE, ALARM WILL BE SLIENT
FOR 10 MINUTES. AFTER 10-MINUTUE SNOOZE INTERVAL, ALARM WILL BE ACTIVE AGAIN. SNOOZE CAN BE
USED FOR REPEATEDLY WITHIN THE 1-HOUR ALARM ACTIVE INTERVAL.
TIMER FUNCTION
1. PUSH THE
POWER KNOB
TILL THE
STANDBY INDICATOR
LIGHT OFF. UNIT IS TURNING FROM STANDBY
MODE TO OPERATION MODE.
2. WHEN THE UNIT IS TURNED ON, PRESS SLEEP BUTTON (3) REPEATEDLY TO CHOOSE THE SLEEP TIME
MINUTES FROM 90>80>704..>10 OFF.
3. SLEEP TIME SETTING IS STORED WHEN THE “SLEEP” ICON LIGHTS UP ON THE DISPLAY.
4. WHEN THE SLEEP TIME MINUTES IS OVER, UNIT WILL BE SWITCHED TO STANDBY MODE
AUTOMATICALLY.
LISTENING TO RADIO
RADIO TUNING
1. PRESS
FUNCTION BUTTON
TO SELECT “TUNE” MODE.
2. SELECT THE DESIRED BAND BY RADIO
BAND BUTTON
(AM OR FM).
3. TUNE TO THE REQUIRED STATION BY PRESSING
SKIP UP OR SKIP DOWN
BUTTON FOR 1-2 SECONDS,
AND THEN RELEASE.
4. THE UNIT WILL START SEEKING AUTOMATICALLY AND STOP WHEN A RADIO STATION IS FOUND.
MANUAL PRESET RADIO STATIONS
1. WHEN THE DESIRED RADIO STATION IS FOUND, PRESS
MODE
BUTTON, PROGRAM NUMBER WILL BE
FLASHING.
2. PRESS
PRESET UP OR PRESET DOWN
TO CHOOSE THE PROGRAM NUMBER FOR STORING THE
DESIRED RADIO STATION.
3. PRESS
MODE
BUTTON AGAIN TO CONFIRM, PROGRAM NUMBER WILL STOP TO FLASH.
4. REPEAT STEP 2 & 3 UNTIL ALL DESIRED RADIO STATIONS IS BEING FOUND AND STORED
5. PRESS
PRESET UP OR PRESET DOWN
TO CHOOSE THE PRESET RADIO STATIONS.
6. THE NUMBER OF STATIONS CAN BE FOUND AND STORED IS DEPENDED ON THE RECEPTION OF
DIFFERENT AREA AND COUNTRIES.
AUTO PRESET RADIO STATIONS
1. DURING RADIO MODE, PRESS THE
PLAY/PAUSE
BUTTON, THE UNIT WILL AUTOMATICLLY SCAN THE
RADIO FREQUENCY. WHEN THE CLEAR SIGNAL IS FOUND, IT WILL AUTOMATICALLY STORE THE RADIO
STATION, STARTING FROM PROGRAM NUMBER 1.
2. THE NUMBER OF STATIONS CAN BE FOUND AND STORED IS DEPENDED ON THE RECEPTION OF
DIFFERENT AREA AND COUNTRIES.
FM & FM-STEREO RECEPTION
PRESS “FM ST.” BUTTON ON THE REMOTE CONTROL TO SELTECT FM MONO OR FM STEREO MODE.
WHEN STEREO SIGNAL ARE WEAK. IT IS PREFERABLE TO RECEIVE THE PROGRAM IN MONO.
“ST” ICON LIGHT UP ON THE DISPLAY TO SHOW FM STEREO MODE IS RECEIVING.
HINTS FOR BETTER RECEPTIO
1. AM: THERE IS A BUILT-IN AM BAR ANTENNA. IF AM RECECPTION IS WEAK, SLIGHTLY ROTATING OR
RE-POSITIONING OF THE UNIT WILL USUALLY IMPROVE THE AM RECEPTION.
2. FM : THE RECEIVER HAS A BUILT-IN FM WIRE ANTENNA HANGING AT THE REAR CABINET. THIS WIRE
SHOULD BE TOTALLY UNRAVELED AND EXTENDED FOR BEST RECEPTION.
FM & FM-STEREO RADIO ENCODING
1. PRESS
FUNCTION
BUTTON TO SELECT “TUNE” MODE AND SELECT THE DESIRED BAND BY RADIO
BAND
BUTTON (AM OR FM).
2. INSERT MEMORY DEVICE (USB DRIVE, SD OR MMC CARD)
3. PRESS THE
REC
BUTTON, IT WILL TAKE 3-5 SECONDS TO READ MEMORY DEVICE. THEN USB OR SD
ICON WILL BE FLASHING.
4. PRESS
SKIP UP
OR SKIP DOWN
BUTTON TO SELECT DESIRED MODE (USB OR SD)
FOR ENCODING. THEN PRESS THE
REC
BUTTON AGAIN TO CONFIRM.
AND THE SYSTEM IS
STARTING THE ENCODING MODE AFTER FEW SECONDSS.
5. IF ONLY USB DRIVE, SD OR MMC CARD IS INSERTED, STEP 4 CAN BE SKIPPED.
6. THE USB OR SD ICON WILL BE FLASHING ON THE DISPLAY DURNIG ENCODING.
7. TO FINISH ENCODING, PRESS
STOP
BUTTON
AND DISPLAY WILL SHOW “END” AND RETURN TO
“ TUNER” MODE.
