TS-5500 User’s Manual
Technologic Systems
10/31/03
26
| <Esc> to continue (no save) |
www.gensw.com
20.2 Basic CMOS Configuration
The “Basic CMOS Configuration” screen allows setup of the Compact Flash or IDE drives, Drive
Assignment mapping and Boot Order, as well as Time, Date and misc. keyboard and memory test
settings. The default settings for the TS-5500 are show below.
+------------------------------------------------------------------------------+
| |
| System Bios Setup - Basic CMOS Configuration |
| (C) 2000 General Software, Inc. All rights reserved |
+---------------------------+--------------------+-----------------------------+
| DRIVE ASSIGNMENT ORDER: | Date:>Dec 14, 2001 | Typematic Delay : 250 ms |
| Drive A: 5300 Flash A: | Time: 09 : 56 : 21 | Typematic Rate : 30 cps |
| Drive B: 5300 Flash B: | NumLock: Disabled | Seek at Boot : None |
| Drive C: Ide 0/Pri --------------------+ Show "Hit Del" : Enabled |
| Drive D: (None) | BOOT ORDER: | Config Box : Enabled |
| Drive E: (None) | Boot 1st: Drive C: | F1 Error Wait : Enabled |
| Drive F: (None) | Boot 2nd: Drive A: | Parity Checking : (Unused) |
| Drive G: (None) | Boot 3rd: DOS-ROM | Memory Test Tick : Enabled |
| Drive H: (None) | Boot 4th: (None) | Test Above 1 MB : Enabled |
| Drive I: (None) | Boot 5th: (None) | Debug Breakpoints: Enabled |
| Drive J: (None) | Boot 6th: (None) | Splash Screen : (Unused) |
| Drive K: (None) +--------------------+-----------------+-----------+
| Boot Method: Boot Sector | IDE DRIVE GEOMETRY: Sect Hds Cyls | Memory |
+---------------------------+ Ide 0: 2 = AUTOCONFIG, PHYSICAL | Base: |
| FLOPPY DRIVE TYPES: | Ide 1: Not installed | 640KB |
| Floppy 0: Not installed | Ide 2: Not installed | Ext: |
| Floppy 1: Not installed | Ide 3: Not installed | 31MB |
+---------------------------+--------------------------------------+-----------+
| ^E/^X/<Tab> to select or +/- to modify |
<Esc> to return to main menu
The factory defaults shown will first attempt to boot from Compact Flash as Drive C:. If no CF is
installed the BIOS will then boot from Drive A:. If a CF is installed, but it is not desired to boot from this
drive, change the “Boot 1
st”
setting to “Drive A:”.
In order for the Compact Flash to function properly as an IDE hard drive, the IDE DRIVE GEOMETRY
must be set to “AUTOCONFIG, PHYSICAL” and the DRIVE ASSIGNMENT ORDER must be set to “Ide
0/Pri Master” or “Ide 2/Sec Master”.
In this example the Compact Flash socket on the TS-5500 (Ide 0) is set as “AUTOCONFIG, PHYSICAL”
and mapped so that drive C: is assigned to “Ide 0/Pri Master”. This drive is also set as the 1
st
boot
device.
20.3 Adding a TS-9400 or TS-9500 with Compact Flash
A TS-9500 may be added to the system, this board has its own Compact Flash socket which may be
set to Primary Master or Secondary Master using the DIP switches. If the TS-9500 CF is set to Primary
Master (DIP switch 5 on), then no CF card may be installed in the TS-5500 CF socket and the CMOS
settings should be exactly as shown above. The TS-9500 CF card will be mapped as Drive C: and will
be the boot drive. If the TS-9500 CF card is set to Secondary Master (Ide 2), then the TS-5500 CF
socket may have a CF installed as Primary Master (Ide 0). To configure the TS-9500 as Secondary
Содержание TS-5500
Страница 1: ...TS 5500 User s Manual...
