TechniSat
®
VC 2002 S
7
PREPROGRAMMING
At the end of this manual you will find a list of all
the preprogrammed TV and radio stations. This
table also contains information on the stored
audio/video parameters which will give you a
guide if you wish to change the preset.
If you are not satisfied with the preprogramming
or if you want to add some channels, you can
programme the receiver to your own require-
ments as described in the section on “Individu-
al Programming” (see below).
i) Using V/H LNB: The TechniSat VC 2002 S is
preprogrammed in accordance with programme
table 1 at the end of this manual.
ii) Using ISISAT LNB: (refer to programme table 2)
If the ISISAST-Preprogramming is called up,
the preprogramming for V/H LNBs does not
meet the table any more, and all programmes
for V/H-LNB need to be programmed again.
1. Switch the receiver to Standby mode (power off)
2. Press both the up and down channel buttons
simultaneously for approx. 3 seconds.
The display will indicate “SEL” (select).
3. You can now select a channel:
Channel up = PRG 1 = Normal programme
Channel down = PRG 2 = ISISAT programme
4. Switch on the receiver (power on).
PREPROGRAMMING IS NOW COMPLETED.
CHANNEL SELECTION: The channel number
selected is shown on the digital display ie. F01-
F99 or C01-C99. Channels preceded with an F
are stored channels and can be accessed eit-
her directly using the up and down keys or by
keying in the respective channel number. Non-
stored channels can only be accessed by key-
ing in the channel number.
INDIVIDUAL PROGRAMMING
It is possible to alter each channel or change the
preset completely if you so wish. Switch to the
channel you would like to alter and enter the video
& audio frequencies, polarisation, bandwidth and
decoder mode (if necessary) as follows:
POLARISATION: Select the required polari-
sation (vertical or horizontal) by pressing the V/H
button on the remote control.
VIDEO TUNING: After pressing either the up
and down tuning key a 3-figure number is sho-
wn on the display (frequency in MHz). To alter
the frequency you have the option of either pres-
sing the up and down tuning keys or the requi-
red frequency can be keyed in directly using the
remote control. Although you must always ent-
er a 4-digit number for the frequency (ie. 0950-
2050) only the last 3 digits are displayed.
DEV SELECTION: ASTRA channels are pre-
programmed Hi (high video level). Other chan-
nels can be programmed Lo (low video level).
AUDIO TUNING:
a) First press either the Mono/Stereo button to
select 0- Mono, 0-0 for Stereo.
b) If stereo is selected the button A/B should be
pressed to obtain A (left) or B (right) side
audio outputs.
c) The correct frequency can be set using the
audio up/down keys. After selecting A or B
the required frequency can be keyed in directly
and will be shown on the digital display.
d) Tune audio bandwidth I---I wide,-II- narrow by
pressing the W/N button.
IF STEREO HAS BEEN SELECTED IT IS
NECESSARY TO REPEAT STAGES b) AND
c) FOR THE OTHER FREQUENCY.
NOTE:
i)
Holding down the AUDIO and TUNING buttons
accelerates the frequency change.
ii) 5 seconds is allowed for keying in the
frequencies directly. If this is not achieved
(ie. entry does not
appear on the display) press the appropriate
TUNING or AUDIO key and re-enter.
STORING: Once you have attained the best
possible picture and sound quality you can sto-
re the channel by using for example a ball point
pen to press the sunken STORE button for 1-2
seconds.
ERASING: To erase stored information press
and hold down the ERASE key as above. Now
the erased channel can only be selected by ente-
ring the number via the key pad of the remote
control (see also CHANNEL SELECTION).
