background image

12

 

 

 

 

 

Operation Guide

                                       

3.1. 

OPERATION OVERVIEW 

This chapter provides information on how to operate the TP400D through front panel 

and WEB GUI. User can select the appropriate operation method to set up the unit.  

3.2. 

POWERING UP AND INITIALIZATION 

Switch on the equipment through the rear power switch, and the unit is powered up and 

starts the initialization process. 

The LCD screen is lighted up, and display information is as follows: 

 

 

The  initialization  takes  about  20  seconds  to  complete,  and  then  the  unit  shows  the  IP 

address information is as follows: 

 

 

Before powering-up the device, make sure that all cabling is 

correctly connected (refer to chapter 3.4 of this manual). Make sure the 
device is correctly connected to the power inlet and is grounded.

 

 If the unit fails to initia

lize and hangs at the “booting” stage, 

switching off the device and then powering up again may help. If the device 

still fails to initialize, please contact your service representative for help. 

 

 

3.3. 

FRONT PANEL OPERATION 

Ways of operation: use the 6 navigation keys on front panel: Up / Down / Left / Right / 

Menu / Ok to configure the TP400D parameters. The configuration and settings are 

displayed through front panel LCD. 

 

 

TP400D Transmodulator/Processor 
IP: 192.168.001.098 

TP400D Transmodulator/Processor 
Setting System… 

Содержание tp400d-8vsb











































Отзывы: