tecan Columbus Washer Скачать руководство пользователя страница 42

Страница: 42 / 82

4. Operating Instructions

4.6 End of Operation

At the end of operation, the instrument can be either left switched on with the
manifold in the rinsing solution or switched off.

Instrument Left Switched On

Use the following procedure to leave the instrument switched on with the
manifold soaking in the distilled water at the end of operation:

Place the wash solution tube into a bottle containing distilled water.

Use the

Rinse: Night

rinsing procedure to rinse the wash system.

See chapter 7.

When the rinsing procedure is completed the following message is displayed:

Soaking
Stop

If the manifold is to be soaked overnight, do not switch the instrument off.

Instrument Switched Off

If the instrument is to be switched off at the end of operation the

Rinse: Day

rinsing procedure should be performed to prevent the needles becoming blocked.

Place the wash solution tube into a bottle containing distilled water.

Use the

Rinse: Day

rinsing procedure to rinse the wash system.

When the rinsing procedure is completed, switch the instrument off.

4-14

Instructions for Use for Columbus Washer No. I 109 006 Rev No. 2.2

May 2003

Содержание Columbus Washer



















































































Результаты поиска

Содержание Columbus Washer

Отзывы:

Похожие инструкции для Columbus Washer

Бренды по названию

Популярные бренды

tecan Columbus Washer, Инструкция по эксплуатации

Результаты поиска

Содержание Columbus Washer

Отзывы:

Похожие инструкции для Columbus Washer

Бренды по названию

Популярные бренды