Tecamp Raptor Top Скачать руководство пользователя страница 9

16 TUNeR

This jack is provided for connection to an electronic 
tuner and is always “live”, even when the Raptor is in 
“BREAK” (#9) mode. This allows for silent tuning as well 
as providing a monitor feed which stays hot even when 
the house mix is muted.

17 LINe OUT

This „LINE OUT PRE MASTER“ jack (#17a) provides a line 
level signal for connection to a separate power amp, PA 
mixing console or recording equipment. The volume of 
the signal is not controlled by the “MASTER” control 
(#8). Note that the output is muted when the “BREAK” 
function (#9) is engaged. The „LINE OUT POST MASTER“ 
jack (# 17b) can connect to an additional power amplifier. 
The volume of the signal is controlled by the “MASTER” 
control (#8). Note that the output is muted when the 
“BREAK” function (#9) is engaged.

18 DI OUT

The RAPTOR supplies a transformer balanced line output 
signal for connecting to a house mixing board, recording 
console or external amplifier(s) with balanced inputs. The 
need for an additional DI box is obsolete. Due to the ad-
vanced valve amp circuit design and the use of only the 
best components available the high sound quality of the 
DI output makes it the amp of choice in any recording 
studio. Connect a shielded 3-core mic cable with XLR 
plugs to the male XLR output (#18). The volume of the 
signal is controlled by the“MASTER” control (#8). Note 
that the output  is muted when the “BREAK” function 
(#9) is engaged.

19 GROUND

The RAPTOR provides a ground lift switch for the “DI 
OUT” (#18), to isolate ground loops in multiple ground-
ing. If you disconnect the wiring to hum with the PA

9

!

HIGH VOLTAGE! CAUTION: TO PREVENT THE RISK OF FIRE AND SHOCK HAZARD 

DON’T EXPOSE THIS APPLIANCE TO MOISTURE OR RAIN. 

DO NOT OPEN CASE. NO USER SERVICEABLE PARTS INSIDE. 

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

11

5

230

2A/SB

HI TENSION 

FUSE

VOLTAGE

SELECTOR

LINE OUT

GROUND

POST MASTER

POST MASTER

PRE MASTER

DI OUT

GRD LIFT

LINE OUT

USE ONLY WITH A 250V FUSE

TUNER

FUSE

 

230 V T 6,3 A (SB) 
115 V T 12 A (SB)

SEND

SERIAL FX LOOP

RETURN

N

E

UTRI

K

N

E

UTRI

K

SPEAKER OUTPUT

IMPEDANCE

2

4

8

17b

18

19

20

21

Содержание Raptor Top













Отзывы: