Team SILK AX14-45 Скачать руководство пользователя страница 86

Страница: 86 / 91

AX14-45 Flange Facing Machine

LIFTING:
ENSURE LIFTING IS CARRIED OUT IN A SAFE AND PROPER

MANNER, IN ACCORDANCE WITH APPLICABLE HEALTH AND

SAFETY REGULATIONS.
ALWAYS KNOW THE WEIGHT OF THE EQUIPMENT AND THE

COMPONENT PARTS.
THE USE OF MECHANICAL LIFTING DEVICES MAY BE A

MANDATORY REQUIREMENT FOR LIFTING THIS EQUIPMENT.

INSTALLATION AND REMOVAL:
THIS EQUIPMENT IS INTENDED TO BE PORTABLE AND MAY BE

USED IN A VARIETY OF LOCATIONS AND ORIENTATIONS. ALWAYS

ENSURE THAT THIS EQUIPMENT IS PROPERLY SUPPORTED AND

RESTRAINED DURING THE INSTALLATION AND REMOVAL

PROCESS.

4. INSTALLATION OF THE EQUIPMENT

INSTALLATION ONTO THE TEAM

AX14-45 FLANGE FACING MACHINE

Inspect the Fall-Stop Kit and confirm that it is complete and fit for purpose.

FALL-STOP KIT

Inspect the TEAM

machine in the location where the fall-stop kit will be installed and

confirm that the M10 tapped holes and the keyway location feature are fit for purpose, see

Fig 1.

Содержание SILK AX14-45




























































































Результаты поиска

Содержание SILK AX14-45

Отзывы:

Похожие инструкции для SILK AX14-45

Бренды по названию

Популярные бренды

Team SILK AX14-45, Инструкция по эксплуатации

Результаты поиска

Содержание SILK AX14-45

Отзывы:

Похожие инструкции для SILK AX14-45

Бренды по названию

Популярные бренды