Team Magic 6SETH, Руководство пользователя

Страница: 3 / 9

3
WP-8BL100-RTR / WP-8BL150-RTR User Manual




Warnings
• Ensure all wires and connections are well insulated before connecting the ESC to related devices.
• Ensure all devices are well connected to prevent poor connection that may cause your vehicle out of control or other unpredictable issues.
• Read throgh the manuals of all power devices and chassis and ensure the power configuration is rational before using this unit.
• Please use a soldering iron with the power of art least 60Wto solder all input/output wires and connectors.
• Do not hold the vehicle in the air and rev it up to full throttle, as rubber tires can expanding to extremely size untill explode and cause serious injury.
• Stop using the ESC when its casing temperature exceeds 90
0
C / 194
0
F to avoid the ESC or the motor gets damaged even destroyed.
( We recommend setting the “ ESC Thermal Protection ” to 105
0
C/ 221
0
F, this refers to the internal temperature of the ESC.)
• We recommend removing the cooling fan from ESC before exposing vehicle to liquids, and fully dry it right after use.
• Always disconnect batteries after use, as the ESC will continue to consume the current power,even if the ESC is turned off.
( A long-time connecting will cause battires discharge completely and break the ESC .
Features
• Completely water-proof and dust-proof. The ESC works properly even under water.
(Please remove the cooling fan when running car in water, and after running, please make the ESC clean and then dry it to
avoid the oxidation of copper connectors)
• External Programming Port (EPP), easy to connect with program card, and also works as power port for cooling fan.
• Excellent start-up, acceleration and linearity features, suitable for truggy (especially short course trucks) and buggy.
• The built-in switching mode BEC has powerful output to supply all electronic equipments.
• There is a mounting stand for installing the ESC on chassis easily and firmly.
• Proportional ABS brake function with 5 steps of maximum brake force adjustment, 8 steps of drag-brake force adjustment.
Also compatible with the mechanical disc-brake system.
• Multiple protection features:
Low voltage cut-off protection / Over-heat protection / Throttle signal loss protection / Motor blocked protection
• Easily programmed with the SET button of the ESC, and also compatible with pocket-sized Program Card.
Specifications
Connection
Cont. / Peak Current
MODEL WP-8BL100-RTR WP-8BL150-RTR
Motor Supported
Cars Applicable
Motor Limit
Resistance
Battery
BEC Output
Programming Port
Dimension
Weight (with wires)
100A / 650A
1/8 Touring Car , SCT, Buggy , 1/10 Truggy, Buggy
4-J1PǣTJ[FNPUPSǢ,7â
4-J1PǣTJ[FNPUPSǢ,7â
0.0005 ohm
$FMMT/J.)Ǣ4-J1P
7"4XJUDINPEF
FAN / PRG Port
59.5(L) × 48(W) × 42(H)
173g
Sensored / Sensorless Brushless Motor (only in sensorless mode)
150A/950A
4-J1PǣTJ[FNPUPSǢ,7â
4-J1PǣTJ[FNPUPSǢ,7â
0.00035 ohm
$FMMT/J.)Ǣ4-J1P
178g
NOTE 1 5IFDPPMJOHGBOTPG&4$JTTVQQMJFECZUIFCVJMUJO#&$TPJUJTBMXBZTXPSLJOHVOEFS7
NOTE 1
WARNING !
For safety, please always keep the
wheels away from the track when
switching on the ESC.
Connect The ESC, Motor, Receiver, Battery And Servo
[ BEGIN TO USE THE NEW ESC ]
The #A, #B, #C wires of the ESC can be
connected with the motor wires freely
(without any sequence). If the motor
runs in the opposite direction, please
swap any two wire connections.
Throttle Range Setting (Throttle Range Calibration)
In order to make the ESC match the throttle range, you must calibrate it when you begin to use a new ESC, or a new transmitter, or change
UIFTFUUJOHTPGOFVUSBMQPTJUJPOPGUIFUISPUUMFTUJDL"57PS&1"QBSBNFUFSTFUD
A Switch off the ESC, turn on the transmitter, set the direction
PGUISPUUMFDIBOOFMUPs3&7sTFUUIFg&1""57sWBMVFPGUISPUUMF
channel to “100%”, and disable the ABS function of your
transmitter.
B Hold the “SET” key and then switch on the ESC, and release
the “SET” key as soon as possible when the red LED begins to
flash.
Note 2
Note 2
If you don’t release the “SET” key as soon as the red LED begins
to flash, the ESC will enter the program mode, in such a case,
please switch off the ESC and re-calibrate the throttle range
again from step A to step D.
C Set the 3 points according to the steps shown in the pictures on the
right side.
1. The neutral point
Move the throttle stick at the neutral point, and then click the SET key,
the green LED flashes 1 time.
2. The end point of forward direction
Move the throttle stick at the end point of forward direction, and then
click the SET key, the green LED flashes 2 times.
3. The end point of backward direction
Move the throttle stick at the end point of backward direction, and then
click the SET key, the green LED flashes 3 times.
D Throttle range is calibrated; motor can be started after 3 seconds.
Check LED Status In Normal Running
•
When the throttle stick is in the neutral range, neither the Red LED nor the Green LED lights up.
•
When the car moves forward, the Red LED solidly lights; the Green LED also lights up when the throttle stick is at the top position.
•
When the car brakes, the Red LED solidly lights; the Green LED also lights up when the throttle stick is at the bottom position and the
maximum brake force is set to 100%.
•
When the car reverses, the Red LED solidly lights.