Team Losi Triple-XT Sport Скачать руководство пользователя

Страница: 1 / 40

OWNER'S

MANUAL

Take your time and pay close attention to detail. Keep this manual for future reference.

Carefully read through all instructions to familiarize yourself with the parts, construction

techniques, and tuning tips outlined in this manual. Being able to grasp the overall design of

your new

Triple-XT

racing truck before beginning the construction process will ensure a smooth

assembly.

Team Losi, 4710 E. Guasti Rd., Ontario, CA 91761

www.TeamLosi.com • [email protected]

NOTE: Using modified motors with any less than 15 turns of wire exceeds the

capacity of the electronic speed control and voids any warranty.

• Service Information:

Electronics (Motor/Radio/Speed Control)

(877) 504 - 0233

• Chassis (All non-electric) (909) 390-9595

P/N 800-0238

Содержание Triple-XT Sport









































Результаты поиска

Содержание Triple-XT Sport

Отзывы:

Похожие инструкции для Triple-XT Sport

Бренды по названию

Популярные бренды

Team Losi Triple-XT Sport, Руководство пользователя

Результаты поиска

Содержание Triple-XT Sport

Отзывы:

Похожие инструкции для Triple-XT Sport

Бренды по названию

Популярные бренды