background image

Mini-DT Manual Page 3

Changing Frequencies/Channels

The Mini-DT radio operates on 27MHz AM and has 6 different frequencies/channels available. Simply put, a frequency 

is like a TV channel. The transmitter you hold in your hand is like the TV station and the model with the matching 
crystal is like your TV tuned exclusively to the channel of that station. The Mini-DT radio is equipped with changeable 
crystals that allow you to change the frequency/channel you operate on. This is especially useful when you want to run 
a group of Losi Mini-DT’s at the same time. When changing crystals/channels, you must always replace the crystals 
as a matched set with one each going in both the transmitter and the receiver in the truck. Each of the 6 different 
channels are numbered and color-coded. Each set includes a unique crystal for the receiver marked (Rx) and one 
from the transmitter marked (Tx). The crystals are changed by gently pulling them out, then lining up the two pins of 

each new crystal with its socket and carefully pushing them into place. DO NOT force them as damage can occur. If 

they do not slide into the socket easily check for bent or misaligned pins.

Channel 1 

Brown 26.995MHz 

(LOSB1094)

Channel 2 

Red 27.045MHz 

(LOSB1095)

Channel 3 

Orange 27.095MHz 

(LOSB1096)

Channel 4 

Yellow 27.145MHz 

(LOSB1097)

Channel 5 

Green 27.195MHz 

(LOSB1098)

Channel 6 

Blue 27.255MHz 

(LOSB1099)

The Transmitter

1. 

Steering Wheel

: Controls direction (left/right) of the 

model.

2. 

Throttle Trigger

: Controls speed and direction (forward/

reverse) of the model.

3. 

Antenna

: Transmits signal to the model.

4. 

On/Off Switch

: Turns the power on/off for the 

transmitter.

5. 

Indicator Lights

: Green (right) light indicates adequate 

battery power. Red (left) indicates signal strength. 

6. 

ST. Trim

: Adjusts the “hands off” direction of the model.

7. 

TH. Trim

: Adjusts the motor speed to stop at neutral.

8. 

Steering Rate

: Adjusts amount front wheels move when 

the steering wheel is turned left and right.

9. 

ST. REV

: Reverses the function of the steering when the 

wheel is turned left or right.

10. 

TH. REV

: Reverses the function of the speed control 

when pulled back or pushed forward.

11. 

Bottom Cover

: Covers and holds the batteries that 

power the transmitter.

12. 

Transmitter Crystal

: Determines frequency/channel 

you transmit on. The receiver must have a matching  
frequency/channel to operate.

1

2

7

8

9

10

6

3

4

5

11

12

Содержание Mini Desert Truck 1:18 RTR











Отзывы: