background image

Page 4

Base Start-up Settings from the Factory

High-Speed Needle—2

3

/

4

 turns out from bottom

Low-Speed Needle—2

1

/

2

 turns out from bottom

Engine Tuning

After the engine is broken in, you can tune it for optimum performance. When 

tuning, it is critical that you be cautious of overheating as severe damage and 

premature wear can occur. You want to make all carburetor adjustments in 

“one hour” increments.

Low-Speed Adjustment

The low speed adjustment affects the idle and slightly-off-idle performance. 

The optimum setting allows the motor to idle for at least 8−10 seconds. The 

model should then accelerate with a slight amount of sluggishness and a 

noticeable amount of smoke. The simplest way to check this is to make sure 

the engine has been warmed up and let the engine idle for 8−10 seconds. If 

the low-speed mixture is so far off that the engine won’t stay running that 

long, turn the idle stop screw clockwise, increasing the idle speed. With 

the engine at idle, pinch and hold the fuel line near the carburetor, cutting 

off the flow of fuel, and listen closely to the engine rpm (speed). If the low-

speed needle is set correctly, the engine speed will increase only slightly and then die. If the engine increases 

several hundred rpm before stopping, the low-speed needle is too rich. Lean the mixture by turning the needle 

clockwise one hour and trying again. If the engine speed does not increase but simply dies, the needle is too 

lean and needs to be richened up by turning the needle counterclockwise one hour before trying again. After 

you have optimized the low-speed setting, the engine will probably be idling faster. You will have to adjust the 

idle stop screw counterclockwise to slow the engine idle speed down. The engine should accelerate at a constant 

pace without hesitating.

Hi-Speed Adjustment

After initial acceleration, the engine should pull at a steady rate while maintaining a two-stroke whine and a 

noticeable trail of smoke. If the engine labors and is sluggish with heavy smoke, the mixture is too rich and needs 

to be leaned by turning the high-speed needle clockwise in one-hour increments until it runs smoothly. If the 

engine isn’t smoking or starts to die after acceleration, it is too lean and you must richen the mixture by turning 

the needle counterclockwise. Don’t be confused by the sound of the engine and the actual performance. A 

leaner mixture will produce an exhaust note with a higher pitch but this does not necessarily mean improved 

performance, as the engine is on the verge of overheating and may incur possible damage. Ideally you want to 

run the engine so that it is on the slightly rich side of optimum. This will give you the best combination of speed 

and engine life. 

CAUTION

: The engine is too lean and overheating if it accelerates rapidly with a high-pitched 

scream then seems to labor, stops smoking, or loses speed. This can be caused by the terrain, atmospheric 

conditions, or drastic altitude changes. To avoid permanent engine damage, 

immediately

 richen the mixture by 

turning the high-speed needle counterclockwise at least “two hours” and be prepared for further adjustments 

before running any more. 

Note

: The normal operating temperature as seen on your radio screen should be in the 

190 to 220° F (88 to 105° C) range.

1 H

our

2 H

our

Carb Adjustments:

Make all carburetor adjustments

in one-hour increments.

Imagine the slot in the needle is

the hour hand on a clock. Adjust

it as though you were moving

the hour hand from one hour to

 the next or previous one.

High-Speed Needle

As you turn this clockwise (leaner),
less fuel enters the engine. 
Turning it counterclockwise 
(richer) allows more fuel to enter 
the engine.

Idle Speed Screw

As you turn this clockwise, it
increases the carburetor opening 
at idle and increases idle speed. 
Turning it counterclockwise 
decreases the opening and idle 
speed.

Low-Speed Needle

As you turn this clockwise (leaner),
less fuel enters the engine. 
Turning it counterclockwise 
(richer) allows more fuel to enter 
the engine.

Richer

Leaner

Idle Speed

Screw

Faster

Slower

High-Speed

Needle

Carb Opening

Leaner

Richer

Low-Speed

Needle

Содержание LST XXL

























Отзывы: