manualshive.com logo in svg

Team Assocciated RC10 B3 Factory Team, Инструкция по сборке и руководство пользователя

Поделиться
Скачать
Team Assocciated RC10 B3 Factory Team Скачать руководство пользователя страница 10

REMOVE THE BACKING
Remove the backing and 
center from the #7373 
gasket.

B A G   D

INSTALL THE MOTOR PLATE
Center the #7373 gasket around the 
large round hole of the 9245 (9245B*) 
plate.
Install the three #9352 spacers.
Line up the #9245 (9245B*) plate and 
fasten with the three #6928 (6935*) 
screws.

7373, qty 1
motor plate gasket
foam

1:1

9352, qty 3
motor plate
spacer

9245, 9245B*, qty 1
motor plate

INSTALL THE ASSOCIATED TORQUE CLUTCH (ATC)
Add the #9251 inner hub to the shaft, lining up the notch with the roll 
pin.
Install the #9253 clutch disc into the inner hub, then add the #9252 
outer hub and #6599 bushing.
Install parts in the following order: #6594 (thin), 6594 (thick), 6594 
(thin), 6587 black spring, 6629 locknut.
Orient the #6693 spur gear side facing out as shown and mount to 
#9252 with two #6568 screws.
Tighten the #6629 locknut so the end of the shaft is flush with the end of 
the nut. This is a good initial adjustment. For further info on the torque 
clutch, see the tuning section on page 27.

MOUNT THE TRANSMISSION
Mount the #9380 brace with two #7874 (7873*) screws.
Mount the tranny with the two #6292 (6934*) screws from below, 
lining up the motor plate holes as shown.
Bolt the motor plate to the rear chassis with two #6568 screws.

6587, qty 1
torque control
spring

6629, qty 1
5-40 locknut

1:1

6594, qty 2
thrust bearing
washer (thin)

6594, qty 1
thrust bearing
(thick gold)

6599, qty 1
3/16 x 3/8
bushing

1:1

6693, qty 1
81T 48 pitch
spur gear

9251, qty 1
inner torque
clutch hub

9252, qty 1
outer torque
clutch hub

9253, qty 1
clutch disc

9380, 9381*, qty 1
rear transmission
brace

7874, 7873*, qty 2
4-40 x 7/16

1:1

6568, qty 4
4-40 x 3/16

6292, 6934*, qty 2
4-40 x 3/8

1:1

1:1

1:1

1:1

1:1

T O O L S   U S E D

s t e p   8

s t e p   1 1
L E F T   S I D E

1/16", 3/32"

s t e p   9

s t e p   1 0

11

7373

9352

9245, 9245B*

9352

9352

9251

9252

9253

6587

6629

6693

6568

6568

6599 bushing

6292, 6934*

6568

6568

7874, 7873*

9380

6594

silver color

6594

gold color

REMOVE THESE 
PARTS FOR:

Steps 8-11

1:1

6928,
6935*

7874, 7873*

6292, 6934*

Содержание RC10 B3 Factory Team


























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды