background image

Fill the unit with cold water until water can be seen
below the baffle.

Do not use pre-heated water as this may damage the
unit.

Do not overfill – if there is water above the baffle use the
tap to reduce the water level before operating.

Close lid and ensure seal is fully engaged.

Connect to the vehicle’s power supply to switch on the
unit.

An orange LED indicates that the power is connected.

Allow to heat up for approximately 15 minutes.

The green LED will light to indicate water is at the
correct temperature.

Use tap to discharge water to wash hands.

If a continuous flow of water is required fully depress
the tap lever.

Note: a removable bowl (part number TW Loose bowl) is
available as an optional extra if you prefer to wash
hands in this manner.

Waste water will drain from the sink, inside the bowl and
down through the waste pipe into a container.

If water sits in the bowl, slowly close the sink to allow
the water to drain away.

When the sink is closed, waste water will flow into the
waste water hose and the waste water container.

When the water tank is empty of water the red LED will
light.

Disconnect the unit and allow to cool before refilling.

LED display

The unit has an LED display to indicate the status.

FLASHING GREEN

- unit on standby. Either waiting for

higher battery voltage or white wire to go to +12V.

SOLID GREEN

- unit at temperature.

SOLID AMBER

- unit heating.

SOLID RED

– no water / tilt fault.

FLASHING RED

- hardware fault.

Operating instructions

Empty the waste water container to a foul water drain
and rinse with clean water. Ensure hose is fully emptied
before removing container, to avoid spills.

If unit is left unused for an extended period it is
recommended that it is emptied of water and
replenished with fresh water.

Clean all surfaces with an anti-bacterial wipe or
disinfectant paying particular attention to frequent

contact points.

Do not use abrasive cleaners which may scratch the
external surfaces.

This unit must not be subjected to a high pressure water
jet.

It is recommended that the unit is cleaned with a
cleaning solution such as Milton according to the
instructions on a weekly basis.

Cleaning instructions

Bowl

ref TW Loose bowl

Towel holder

ref GENTWLHLDR

Soap bottle and bracket ref GENSOAPDISP/BRKT

Waste water container

ref 10 ltr SPARETAINERASSY

Waste water container

ref 20 ltr SPAREBSBLK

Waste water container

ref 25 ltr SPAREBSWH

Optional extras

At the end of its useful life, the
handwash unit should not be disposed
of in general household waste.

Units should be taken to a recycling
facility for electrical and electronic
items.

Please see WEEE regulations.

Disposal

Содержание TEALwash








Отзывы: