34
Radio
Cannot listen to any station, or signal is too weak.
e
Tune in the station properly.
e
Rotate the DAB/FM antenna for the best reception position.
Though the FM broadcast is stereo, it sounds monaural.
e
Press the FM MODE button.
‘NO stations available’ appears on the display.
e
Check that antenna is stretched.
e
Ensure that DAB coverage exists in your area.
Cannot access secondary services.
e
Secondary service is part-time programme transmitted as a
side channel of the primary station. When you want to listen
to a secondary station, check its broadcasting schedule.
Display goes out or displays ‘Station off-air’.
e
This may occur if a broadcaster changes the label of a
service or removes a label whilst you are listening to it. The
CX-200iDAB will try to retune to this station, or alternatively
follow the procedure for auto tune on page 22.
Cannot listen to the selected station.
e
Ensure you have pressed the SELECT button when you want
to listen to your selection. The station you are currently
listening to will be displayed on the first line of the display,
as you scroll through the station order list the second line
will show other station options. Press the SELECT button to
activate your selection.
A burbling sound is heard on some stations.
e
DAB like other digital media is good at producing quality
audio from a low level signal. However, if this signal level is
too low, a ‘burbling’ sound can sometimes be heard. To
reduce this, try repositioning your antenna to gain maximum
signal strength.
If normal operation cannot be recovered, unplug the
power cord from the outlet and plug it again.
If the power switch of the subwoofer turned off, the
settings kept in memory (clock, timer setting) will be
erased.
Beware of condensation
When the unit (or a disc) is moved from a cold to a warm
place, or used after a sudden temperature change, there is a
danger of condensation; vapor in the air could condense on
the internal mechanism, making correct operation erratic or
impossible. To prevent this, or if this occurs, leave the unit for
one or two hours with the power turned on. The unit will
stabilize at the temperature of its surroundings.
Maintenance
If the surface of the unit gets dirty, wipe with a soft cloth or
use diluted mild liquid soap. Never spray liquid directly on this
unit. Apply your cleaner to your cleaning cloth and wipe
gently. Be sure to remove any excess completely. Do not use
thinner, benzene or alcohol as they may damage the surface
of the unit. Allow the surface of the unit to dry completely
before using.
If you have problems with your system, look through this chart
and see if you can solve the problem yourself before calling your
dealer or TEAC service center.
General
No power
e
Check the connection to the AC power supply. Check and
make sure the AC source is not a switched outlet and that,
if it is, the switch is turned on. Make sure there is power to
the AC outlet by plugging another item such as a lamp or
fan into the outlet.
No sound from speakers.
e
Select the source by pressing the FUNCTION button.
e
Check the connection to the speakers.
e
Adjust the volume.
e
Pull out the headphone’s plug from the PHONES jack.
e
If ‘Muting’ is blinking, press the MUTING button.
The sound is noisy.
e
The unit is too close to a TV or similar appliances. Install the
unit apart from them, or turn them off.
Remote control doesn’t work.
e
Press the STANDBY/ON switch to turn the unit on.
e
When the battery has run out, put in a new one.
e
Use remote control unit within the range (5 m) and point at
the front panel.
e
Clear obstacles between the remote control unit and the
main unit.
e
If a strong light is near the unit, turn it off.
CD Player
Will not play.
e
Load a disc with the playback side facing away.
e
If the disc is dirty, clean the surface of the disc.
e
A blank disc has been loaded. Load a prerecorded disc.
e
Depending on the disc, etc. it may not be possible to play
back CD-R/RW discs. Try again with another disc.
e
You cannot play back unfinalized CD-R/RW discs. Finalize
such a disc in a CD recorder and try again.
Sound skips.
e
Place the unit on a stable place to avoid vibration and shock.
e
If the disc is dirty, clean the surface of the disc.
e
Don’t use scratched, damaged or warped discs.
iPod Player
Cannot insert the iPod.
e
Check the dock adapter.
e
Remove dust or obstacles from the Dock connector of the
CX-200iDAB and the iPod, and insert the iPod again.
Will not play.
e
Remove the iPod from the dock, wait a few seconds, and
insert it again.
e
Software update may solve the problem. Visit the Apple
website and download the latest iPod Software.
Troubleshooting
