background image

 

Front Panel

 

TEAC CD-RW Installation Guide

2

 

Front Panel

 

disc tray:

 

 Use the disc tray to load CDs into the drive. You can open the tray by 

pressing the eject button or by using the emergency eject mechanism. You can 
close the tray by pressing the eject button.

 

 

 

headphone jack:

 

 You can connect headphones or external speakers to this jack 

to listen to an audio CD being played on your TEAC drive. Use a 3.5 mm stereo 
mini-plug. For external speakers, connect a stereo adapter to split the output into 
separate cables for the left and right channels. Such adapters convert a male 
stereo mini-jack to two female phono jacks.

 

volume control:

 

 Use the volume control to adjust the volume. Turn the control 

right to increase the volume, left to decrease. (Lower the volume before you start 
a CD-ROM audio program to protect your hearing and the audio speakers.)

 

LED indicators:

 

 The drive features two LED indicator lights on the front panel. 

Various operations are indicated as per the following table:

 

emergency eject mechanism:

 

 If the eject button fails, you can 

 

turn off the 

power to the CD-RW drive 

 

and insert a small, thin rod (such as a straightened 

paper clip) into the emergency eject mechanism opening and press firmly to 
eject the disc.

 

eject button:

 

 Press this button to open or close the disc tray. (Some CD-ROM 

titles disable the manual eject button and rely on software commands to eject the 
disc. Refer to the documentation for these titles for more information.)

 

Note:

 

 We strongly recommend that you do not push the tray in to close it. 

Please press the eject button to eject or retract the tray.

 

Operation

Right LED

Left LED

 

At tray loading

green LED flashes

off

At tray eject

green LED flashes

off

During write/erase

off

green LED flashes

During audio play

green LED flashes

off

During seek/data transfer

green LED lights

off

Caution: 

Do not attempt to use the emergency eject mechanism when either 

the Power or Busy indicator is lit or you may seriously damage the disc or 
the CD-RW Drive.

 

CDRW8x8x32short.fm  Page 2  Thursday, October 19, 2000  9:58 PM

All manuals and user guides at all-guides.com

Содержание CD-258 E









Отзывы: