Teac 8886 - Photosmart Camera Dock Digital Docking... Скачать руководство пользователя страница 4

 

Installing the CD-RW Drive

 

TEAC CD-RW Installation Guide

4

 

Installing the CD-RW Drive

 

This section explains how to install the TEAC CD-RW Drive into an IBM PC or 
compatible personal computer. Follow the steps below and refer to your computer 
documentation for information specific to your system.

 

1.

Turn off the power to the computer system and any external devices con-
nected to it.

2.

Touch the exposed metal frame of the computer to ground yourself.

 

This will prevent damage to the computer or CD-RW drive that may be caused 
by a discharge of static electricity.

 

3.

Remove your computer’s cover, faceplate, or 5.25-inch bay cover, as well 
as mounting clips, screws, and retaining brackets.

4.

If you have a SCSI CD-ROM drive or no IDE CD-ROM/DVD drive 
installed on your system, do the following:

4a)

 

 Confirm that the jumper on the rear panel of the CD-RW drive is configured 

to its default setting of Master.

 

4b) 

 

Slide the CD-RW drive into the empty 5.25-inch drive bay. Install the CD-

RW drive in your personal computer in a horizontal orientation (within ±10˚ 
of horizontal). The eject button should be located on the right side of the 
unit. Secure the drive using 3x5mm mounting screws.

 

4c) 

 

Locate the secondary IDE connector on your system’s motherboard and 

connect one end of the IDE interface cable.

Be certain to connect Pin-1 of the interface cable to Pin-1 on the secondary 
IDE connector on the motherboard. (Pin-1 on interface cable is usually 
designated by a color strip along one edge of the cable. Also, the interface 
ribbon cable connector may feature a tab on one side. Insert the cable so that 
the tab aligns with the notch on the interface connector. Do not use 
excessive force while trying to insert the cable into position).

 

Note:

 

 If you have a SCSI CD-ROM drive or no IDE CD-ROM/DVD drive 

installed in your system, continue with Step 4. If you have an IDE CD-ROM/
DVD drive installed in your system, skip step 4 and continue with Step 5.

 

Warning: 

 

Do not use mounting screws longer than 3x5mm to secure the 

CD-RW drive or you may damage the unit.

secure drive with 3x5mm screws

 

CDRW8x8x32short.fm  Page 4  Thursday, October 19, 2000  9:58 PM

Содержание 8886 - Photosmart Camera Dock Digital Docking...









Отзывы: