background image

408-35308 

Rev

 A

 

of 8

 

3.

 

INSTALLING THE DIE SET AND LOCATOR ASSEMBLY 

1.  Open the tool handles. 

2.  Remove the two die-retaining screws from the tool jaws (see Figure 1)

3.  Insert the wire anvil and insulation anvil in the moving jaw of the tool frame with their chamfered sides 

and the marked surfaces facing outward. 

4.  Insert two die-retaining pins. 

5.  Insert the short die-retaining screw through the jaw and through the anvil dies. Tighten the screw just 

enough to hold the die in place. Do 

not

 tighten the screw completely. 

6.  Insert the wire crimper and insulation crimper in the stationary jaw of the tool frame with their 

chamfered sides and the marked surfaces facing outward. 

7.  Insert two die-retaining pins. 

8.  Insert the long die-retaining screw through the jaw and through the crimper dies. Tighten the screw just 

enough to hold the die in place. Do 

not

 tighten the screw completely. 

9.  Carefully close the tool handles, making sure the anvil and crimper align properly. Continue closing the 

tool handles until the ratchet in the tool frame engages sufficiently to hold the dies in place. 

10.  Tighten both die-retaining screws. 

11.  Place the locator assembly over the end of the long screw and position the locator assembly against 

the side of the tool jaw. 

12.  Place the nut onto the end of the long screw and tighten the nut enough to hold the locator assembly in 

place, while still allowing the locator blade to slide up and down. 

4.

 

REMOVING THE DIE SET AND LOCATOR ASSEMBLY 

1.  Close the tool handles until the ratchet releases. 

2.  Remove the nut, the locator assembly, the two die-retaining screws, and the four die-retaining pins. 

3.  Slide the dies out of the tool jaws. 

NOTE 

The ratchet release has detents with audible clicks as the handles are closed. The ratchet releases on the sixth click. 

 

 

Содержание 2407132-1









Отзывы: