TE PRODUCT
PART NUMBER
DESCRIPTION
1479245-1
CONNECTING BLOCK ASSEMBLY, 4 Pair
1479246-1
CONNECTING BLOCK ASSEMBLY, 5 Pair
1479247-1
WIRING BLOCK ASSEMBLY, 50 Pair with Mounting Legs
1479248-1
WIRING BLOCK ASSEMBLY, 100 Pair with Mounting Legs
1479249-1
WIRING BLOCK ASSEMBLY, 300 Pair with Mounting Legs
1479250-1
WIRING BLOCK ASSEMBLY, 50 Pair without Mounting Legs
1479251-1
WIRING BLOCK ASSEMBLY, 100 Pair without Mounting Legs
1479252-1
KIT, 50 Pair with Mounting Legs and 4 Pair Connecting Blocks
1479253-1
KIT, 50 Pair with Mounting Legs and 5 Pair Connecting Blocks
1479254-1
KIT, 100 Pair with Mounting Legs and 4 Pair Connecting Blocks
1479255-1
KIT, 100 Pair with Mounting Legs and 5 Pair Connecting Blocks
1479256-1
KIT, 300 Pair with Mounting Legs and 4 Pair Connecting Blocks
1479257-1
KIT, 300 Pair with Mounting Legs and 5 Pair Connecting Blocks
1479258-1
FRAME KIT, 300 Pair, with 4 Pair Connecting Blocks
1479259-1
FRAME KIT, 300 Pair, with 5 Pair Connecting Blocks
1479260-1
FRAME KIT, 900 Pair, with 4 Pair Connecting Blocks
1479261-1
FRAME KIT, 900 Pair, with 5 Pair Connecting Blocks
1479262-1
PANEL ASSEMBLY, Wiring Block, 100 Pair
1479263-1
PANEL ASSEMBLY, Wiring Block, 200 Pair
1479264-1
PANEL ASSEMBLY, Wiring Block, 400 Pair
Wire
Inserter
Cut Blade
Insert
Impact
Handle
Holder
© 2011 Tyco Electronics Corporation, a TE Connectivity Ltd. Company
All Rights Reserved
*Trademark
TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product and/or Company names may be trademarks of their respective owners.
1 of 3
Instruction Sheet
TOOLING ASSISTANCE CENTER 1-800-722-1111
PRODUCT INFORMATION 1-800-522-6752
This controlled document is subject to change.
For latest revision and Regional Customer Service,
visit our website at www.te.com
LOC B
408-8852
4-Pair Punch Down Tool 1725062-1
22 AUG 11 Rev A
PROPER USE GUIDELINES
Cumulative Trauma Disorders can result from the prolonged use of manually powered hand tools. Hand tools are intended for occasional use
and low volume applications. A wide selection of powered application equipment for extended-use, production operations is available.
Figure 1
1. INTRODUCTION
The 4-Pair Punch Down Tool 1725062-1 shown in
Figure 1 is used to insert and trim wire with the
110Connect XC Category 6 connecting blocks, wiring
blocks, and kits listed in Figure 1. The tool is also used
to install the connecting block to the index strip of the
wiring block. For more information on the installation
of connecting blocks and wiring blocks, refer to
instruction sheet 408-8823.
2. DESCRIPTION
The 4-Pair Punch Down Tool is equipped with an
impact mechanism to provide the force required to
insert and trim 4 pairs of wire at once. The tool is also
equipped with a reversible cut blade if the wires are
not to be trimmed.
DANGER
STOP
The 4-Pair Punch Down Tool contains a sharp
cutting blade. Improper use of tool may result in
damage to the tool or bodily injury.
3. CONNECTING BLOCK INSTALLATION PROCEDURE
Installation of the connecting block to the index strip
may be made easier through the use of the 4-Pair
Punch Down Tool. Refer to Figure 2.
4. INSERTING AND TRIMMING WIRE PROCEDURE
1. Hand lace each wire into the appropriate slot on
the connecting block or index strip.
2. Align the inserter blades on the tool with the
wires.
