background image

INSTRUCTION MANUAL

CHVM2 Series

TDK­Lambda

<Page>

■ ON/OFF Control

By opening and closing the ON/OFF pin and ­Vin pin the external voltage can be turned on and off.

Between the ON/OFF pin (5) and ­Vin pin (2)

1) Open will turn the output ON
2) Short(0 to 1.0V

1mAmax) will turn the output OFF

The ON/OFF pin is internally pulled up to the +Vin, so be careful of the voltage from the switching element 

of the ON/OFF pin (photo couplers, transistors, etc)
Keep the (5) open when not using the ON/OFF control.

The chattering to the ON/OFF pin will affect the output voltage, so choose one without any chattering. 

When the output is turned off by ON/OFF control, the residual output voltage should be within 0.5%.

■ Over current protection

The CHVM series installed the  over current protection  to protect from the over load and load short. When the 

product status is in over load or load short mode, the output voltage will be decreased, and once the problem
has been removed, the voltage will automatically recover.

The over current protection has a hold back characteristic.

The load should be set more than minimum resistor value which according to each series.

7/11

-Vin

ON/OFF

(5)

 

(2)

 

 

Non-isolation type

-Vin

ON/OFF

(5)

(2)

Isolation type

10


80 

60 

40 

20 

0

0 Output current (lo)

100

100% output

50% output

O

utp

ut 

vo

lta

ge

 s

et 

va

lu

e

(%)

CHVM Series

Over current protection 

characteristic

Содержание CHVM2 Series












Отзывы: