background image

FBD120/180/200/220 SECTIONAL GARAGE DOOR OPENER 

15 

 

 
P4. Automatic Closing
 

(1~9 minutes adjustable) (Fig.16) 

1.

 

Press and hold “SET” button for 4 seconds until ‘P1’ displayed.   

2.

 

Press “UP” button three times until ‘P4’ is displayed on the LED. 

3.

 

Press the “SET” button.   

4.

 

Press “UP” or “DOWN” to set auto close time (b0-b9). Press “UP” to increase timer, 

press “DOWN” to decrease timer.   

Note: Set timer to ‘b0’ to disable auto close function. 

5.

 

Press SET to confirm the setting. 

NOTE:   

 

When using auto close mode, a photo electric beam must be fitted correctly and tested for 
operation at regular intervals. Extreme caution is recommended when using auto close mode. 
All safety rules must be followed. 

 

 

Automatic closing is available only when the door is in fully opened position.

 

 

SET

UP

SET

UP

SET

UP

SET

UP

SET

UP

Press and hold “SET” button

for 4 seconds until ‘P1’ is
displayed

Press “SET” button to confirm

Press “UP” or “DOWN” to set auto

close time (b0-b9). Press “UP” to

increase timer, press “DOWN” to

decrease timer.

Note: Set timer to ‘b0’ to disable

auto close function.

Press “SET” button to confirm the

setting

Press “UP” button three times

until ‘P4’ is displayed on the

LED

 

Fig.16 

Содержание FBD180





















Отзывы: