EN
17
English
Chapter 6 - Network
Connecting to a wireless network
Your TV is equipped to be connected to your home
network wirelessly. To do that you need a wireless
router or modem.
1.
Press
on the remote control, select
Network >
Internet connection
and press
OK/►
to enter.
2.
Press
▲
/
▼
to select
On
and press
OK
to confirm.
3.
Press
▲
/
▼
to select
Interface
and press
OK/►
to
enter.
4.
Press
▲
/
▼
to select
Wireless
and press
OK
to
confirm.
5.
Press
▲
/
▼
to select
Wireless settings
and press
OK/►
to enter. You can set the wireless network
connection in 3 ways:
-
a) Scan
• Press
▲
/
▼
to select
Scan
and press
OK/
►
to enter. The TV will search all access points
within range. Access points found by the TV will
be displayed.
• Press
▲
/
▼
to select an available access point,
then press
OK/
►
to connect.
• Press
to return to the
Wireless settings
menu.
Note: If you select a protected access point,
you will have to enter the corresponding
password. Press
OK
on the remote control
to display the virtual keyboard to enable you
to enter the password.
-
b) Manual
Press
▲
/
▼
to select
Manual
and press
OK/
►
to
enter. You will be prompted to enter the correct
SSID of an available wireless router to set up the
connection. Press
to return to the
Wireless
settings
menu.
-
c) Auto
If your AP (Access Point) supports WPS (Wi-
Fi Protected Setup), you can connect to the
network via PIN (Personal Identification Number)
or PBC (Push Button Configuration). WPS will
automatically configure the SSID and WPA key
in either mode.
Press
▲
/
▼
to select
Auto
and press
OK/
►
to
enter.
•
PIN
: Select
PIN
and press
OK/
►
to enter.
Choose a random PIN code. Make sure
this code is installed on the AP. (For the
procedures, refer to your router manual.) Select
OK
and press
OK
to set up the connection.
•
PBC
: If your router has a PBC push button,
select
PBC
and press
OK/
►
to enter. Press
the PBC push button on your router within 2
minutes before you select
OK
and press
OK
again. Your TV will automatically acquire all the
network setting values it needs and connect to
your network.
Network connection
You can set up your TV so that it can access the
Internet through your local area network (LAN) using
a wired or wireless connection.
Connecting to a wired network
You can connect your TV to your LAN using cable in
three ways:
• You can connect your TV to your LAN by connecting
the LAN port on your TV to an external modem
using a Cat 5 cable.
• You can connect your TV to your LAN by connecting
the LAN port on your TV to an IP sharer, which is
connected to an external modem. Use Cat 5 cable
for the connection.
• Depending on how your network is configured, you
may be able to connect your TV to your LAN by
connecting the LAN port on your TV directly to a
network wall outlet using a Cat 5 cable. Note that
the wall outlet is connected to a modem or router
elsewhere in your house.
1.
Press
on the remote control, select
Network >
Internet connection
and press
OK/►
to enter.
2.
Press
▲
/
▼
to select
On
and press
OK
to confirm.
3.
Press
▲
/
▼
to select
Interface
and press
OK/►
to
enter.
4.
Press
▲
/
▼
to select
Ethernet
and press
OK
to
confirm.
5.
Press
▲
/
▼
to select
IP settings
and press
OK/►
to enter. You can set
Address type
to
Auto
or
Manual
.
- Select
Auto
if you want the TV to acquire and
enter the needed IP address automatically.
- Select
Manual
if you want to enter your IP
address manually, then:
• Press
▼
to go to the first entry field.
• Enter the
IP address
,
Subnet mask
,
Default
gateway
,
Primary DNS
and
Secondary DNS
values. Use the numeric buttons to enter
numbers and the
▲
/
▼
/
◄
/
►
buttons to move
from one entry field to another.
- Once
IP setting
is completed, press
▲
/
▼
/
◄
/
►
to select
OK
and press
OK
to confirm. The set
will try to connect to the network and inform
you about the result. Press
to return to the
Network
menu.
6.
If you want to check the information on current
connection, such as
Interface
,
Address type
,
IP
address
, etc., press
▲
/
▼
to select
Information
and press
OK/►
to enter. Press
to return to the
Network
menu.
7.
If you want to check the Internet connectivity, press
▲
/
▼
to select
Connection test
and press
OK/►
.
