TCi HGP HarmonicGuard Series Скачать руководство пользователя страница 27

Страница: 27 / 67

HGP Kit Manual

5.0 PQconnect

Reference Drawing

PKPQ5

for complete board mounting with the bracket.

When mounting the bracket into the enclosure there are three guidelines to follow.

1. Determine best location where there is adequate ventilation, depth for components,

and cables; away from any heat source.

2. The inside surface of the enclosure must be free of protrusions or obstructions in the

area where the PQconnect board will rest.

3. Drill holes as needed per dimension provided.

To ensure the board has a solid ground connection. The metal stud and nut provided with the kit

will need to installed onto the grounding pad of the board.

Figure 14

below indicates the location

of the ground connection.

Wiring

When selecting a mounting location for the PQconnect PCB, plan for the routing of the power

wiring. Make sure all wiring conforms to the requirements of the NEC electrical codes and can

handle the max current required.

PCB Connections

Most connections to PQconnect will be made on the PCB. Refer to connection diagrams in Figure

13. The details of the power and communications terminals are shown in Table 8: Power &

Communications Terminals. Form C relays are available on the PCB, these connections are

shown in Table 10: Form C Relay Contacts. Two relay outputs are available on the PCB.

The relay contactor control command output connection on J11 of the PCB allows the user to

open/close the contactor of the HGP filter. The second relay (output connections on J12) is

optional and could be used for a second contactor for dual tuned circuit filters or as a secondary

status detection.

Содержание HGP HarmonicGuard Series




































































Результаты поиска

Содержание HGP HarmonicGuard Series

Отзывы:

Похожие инструкции для HGP HarmonicGuard Series

Бренды по названию

Популярные бренды

TCi HGP HarmonicGuard Series, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание HGP HarmonicGuard Series

Отзывы:

Похожие инструкции для HGP HarmonicGuard Series

Бренды по названию

Популярные бренды