TCi HGP HarmonicGuard Series Скачать руководство пользователя страница 30

Страница: 30 / 67

HGP Kit Manual

5.0 PQconnect

Table 10: Form C Relay Contacts/ Customer Inputs/Outputs

Terminal

Pin

Description

Label

Tightening Torque

Wire Range

1, 2

Multi-functional

digital Input 1

Customer contact,

normally open

3.5 lb-in (0.4 Nm)

28-12 AWG

1, 2

Multi-

functional

digital Input 1

Customer contact,

normally open

3.5 lb-in (0.4 Nm)

28-12 AWG

J11

Digital output

form C Contact

Normally Closed (NC)

4.4 lb-in (0.5 Nm)

28-14 AWG

Common (COM)

Normally Open (NO)

J10

Digital output

form C Contact

Normally Closed (NC)

4.4 lb-in (0.5 Nm)

28-14 AWG

Common (COM)

Normally Open (NO)

Note

: Form-C relay contacts are gold plated with a load rating of 5.0A @ 120VAC

The filter is set to control the contactor pickup/drop-out at 30% of load current by factory

default. This setting can be changed in the tech access page from the settings menu.

Multi-functional digital inputs

have the following functions:

•

3 = Reset Command

•

4 = External Control Input

Digital Output form C Contact

•

J11 reserved for contactor control

•

J10 used for status detection

PQconnect PCB Calibration

Once the PQconnect connections are made the PCB must be calibrated to the HGP filter

components to ensure proper accuracy and operation of the completed filter. The following steps

will allow for units to be properly calibrated.

Note:

Instillation of the PQvision desktop interface is required for calibration. Please see next

section “PQvision Software” before proceeding with PCB calibration.

Equipment:

Calibrated current clamp meter, laptop, RS485 to USB converter

Step 1:

After assembling HGP with PQconnect, ground the filter and install

only the line side

connections

to the appropriate phases first.

Do not install the load side connections for

calibration process

Ensure communication connections and voltage sense wires are made, follow Table 8: Power &

Communications Terminals for further detail.

Step 2:

Energize filter

Step 3:

Open PQvision interface and connect to a communication port

•

A “CONNECTED” message will appear verifying that the RS485 converter is connected

to the board.

•

If there are any difficulties communicating to the desktop interface, a “NO COM” message

will appear. Refer to the Trouble Shooting section for possible solutions.

•

DEFAULT: 0 = Disabled

•

1 = Tuning Reactor Thermal Switch Input

•

2 = Line Reactor Thermal Switch Input

Содержание HGP HarmonicGuard Series




































































Результаты поиска

Содержание HGP HarmonicGuard Series

Отзывы:

Похожие инструкции для HGP HarmonicGuard Series

Бренды по названию

Популярные бренды

TCi HGP HarmonicGuard Series, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание HGP HarmonicGuard Series

Отзывы:

Похожие инструкции для HGP HarmonicGuard Series

Бренды по названию

Популярные бренды