TCi HGP HarmonicGuard Series Скачать руководство пользователя страница 10

Страница: 10 / 67

HGP Kit Manual

3.0 Pre-Installation Planning

3.0

Pre-Installation Planning

Verify the Application

The HGP is a drive-applied harmonic filter designed and developed by TCI to reduce the harmonic

currents drawn from the power source by VFDs. The published HGP voltage, Power (HP or kW)

and current ratings apply to matching power (HP or kW) rated standard VFDs with six-pulse diode

bridge rectifiers. The HGP may also be sized to filter other loads such as SCR six-step drives,

SCR Direct Current (DC) motor drives, thyristor furnaces, battery chargers, electroplating supplies

or other types of nonlinear loads. In many cases, the filter power rating (HP or kW) will differ from

load power rating (HP or kW). Please contact TCI Technical Support for additional information

and support on sizing HGP harmonic filters for your non six-pulse diode front end VFD

applications.

The HGP is a passive filter connected in series with the input terminals of a VFD or several VFDs

that operate as a group. It is designed to provide a low impedance path for the major harmonic

currents demanded by the drive.

Recommendations Kit Usage

Panel design using a TCI HGP Filter Kit should be performed with appropriate engineering

supervision so the design meets the requirements based on materials utilized in the construction of

the panel, wiring practices followed by your shop, and the actual ambient conditions of the

components for each application.

HGP Kit Part Numbering System

Figure 1: HGP Kit Part Numbering System

Содержание HGP HarmonicGuard Series




































































Результаты поиска

Содержание HGP HarmonicGuard Series

Отзывы:

Похожие инструкции для HGP HarmonicGuard Series

Бренды по названию

Популярные бренды

TCi HGP HarmonicGuard Series, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание HGP HarmonicGuard Series

Отзывы:

Похожие инструкции для HGP HarmonicGuard Series

Бренды по названию

Популярные бренды