10
INSTALLING ADDITIONAL I/O CARDS
I/O Cards
I/O cards MUST be mounted in slots A, B and C
consecutively starting in slot A. Dip-switches must be
correctly set on the I/O cards.
To install an ADA 24/96 or AES-8 card in your
Mainframe
1.Switch OFF the unit and disconnect the main
power cord.
2.Remove the DUM-1 option plate(s) or module by
loosening the 2 screws.
3.Insert the card gently and mount the two screws.
ADA 24/96 cards can be mounted in slots A, B or C.
The AES-8 card
must
be placed in the AES slot.
Static Electricity
As all computer hardware can be sensitive to static
electricity, certain precautions must be taken to protect it
from damage during storage and handling.
Storage
Non-mounted modules should always be stored in
anti-static shielded bags.
General Handling
When inserting or removing any modules, avoid touching
the circuit board by handling only the rear panel of the
module. To minimize the static potentials that can cause
damage to the electronic circuits, you should observe
precautionary grounding techniques such as touching a
grounded DB-8 Mainframe immediately before inserting
modules.
Removing Modules
Before removing any card from your Mainframe, switch off
the power and unplug the main power cable. Unplug all
other connections from the module before unscrewing the
two screws securing the module in the Mainframe. When
removing a module from a Mainframe, the card should be
mounted directly in another Mainframe or placed in an
antistatic shielded bag.
Slot A
Slot B / AES-8
Slot C
Dip 1
Dip 2
Dip 3
Dip 4
Slot A
on
off
off
off
Slot B
on
on
off
off
AES-8
off
on
off
off
Slot C
on
off
on
off
Mounting Modules
Before mounting modules in your DB-8, switch off the
power and unplug the main power cable. Remove the
dummy-panel or original module from the slot where you
want to install the module. The module should then be
removed from the shielded bag and mounted directly in the
Mainframe by handling the rear panel of the module only.
Avoid touching any components on the PCB-Board.
ADA 24/96 Parameters
To access card specific parameters via the TC Icon:
• Press
Frame, System, I/O
and
Slot A
,
Slot B
or
Slot C.
Level In
Changes the analog nominal Input level b6dBu
and +30dBu in 6dB increments.
The analog Input level enables you to match the DB-8
Mainframe Input to the Output of e.g. your mixer. If the
nominal operating level your mixer is e.g. +4dBu and you
12dBu on the Level In parameter you will have a
headroom of 8dB. If you 16dBu in the Analog In the
headroom will be +12dB, and so forth.
Level Out
Changes the analog Output level b6dBu and
+24dBu in 6dB increments.
Filter
Select filter type. Chose between - Linear, Natural, Vintage,
Bright and Standard (Std). Further information on these
filters please read the chapter: In Depth Information.
Soft Clip
Softclip algorithm running in the 96kHz domain right after
the AD conversion before the down-sampling filter.
Output Connection
Please select the type of connection you are using on the
Output of the card. Select between:
Balanced or unbalanced (with signal on pin 2 or pin 3).
If you are connecting unbalanced cables to the
Outputs when Outmode set to BAL, the Outputs will
be muted due to the short circuit the unbalanced cables
cause.
Caution!
The servicing instructions are for use
by qualified personnel only. To
reduce the risk of electric shock do
not perform any servicing other than
that in the operation instructions
unless you are qualified to do so.
