A
B
C
D
E
F
INSTALLATION INSTRUCTIONS
CUSTOMER SERVICE WEST 1-800-267-4774 | EAST 1-800-387-7064 | taymor.com
® REGISTERED TRADEMARK OF TAYMOR INDUSTRIES LTD.
A
B
TURN OFF
TURN OFF
4
A
B
D
C
B
E
F
A
A
F
G
H
SIL
IC
ON
E
B
SI
LI
CO
NE
I
J
H
E
C
D
THIS FAUCET MEETS OR EXCEEDS THE FOLLOWING STANDARDS:
cUPC, ASME A112.18.1, NSF-61 AND LOW LEAD COMPLIANT
1 - O-RING
2 - HANDLE
3 - HANDLE SEAT
4 - HANDLE SCREW
5 - SLEEVE
6 - RETAINER NUT
7 - WASHER
8 - CARTRIDGE
9 - SEAT
10 - SPRING
11 - SCREW
12 - BASE PLATE
13 - MOUNTING NUT
15 - AERATOR
16 - POP-UP
17 - LIFT ROD
19 - WASHER
20 - NUT
21 - SPRING
CLIP
22 - BALL ROD
23 - LIFT
STRAP
18 - FLANGE
C
14 - COUPLING NUT
EXPLODED DIAGRAM FOR REFERENCE
MAINTENANCE
Your new faucet is designed for years of trouble-free performance. Keep it looking
new by cleaning it periodically with a soft cloth. Avoid abrasive cleaners, steel wool and harsh
chemicals as these will dull the finish and void your warranty.
THANK YOU
FOR PURCHASING THIS TAYMOR PRODUCT. ALL TAYMOR PRODUCTS ARE CAREFULLY
ENGINEERED AND FACTORY TESTED TO PROVIDE LONG TROUBLE-FREE USE UNDER NORMAL CONDITIONS.
HAVE BASIC TOOLS READY
RECOMMENDED TOOLS:
1
Flashlight
Teflon tape Screwdrivers
Adjustable
wrench and
pipe wrench
Plumber’s putty
Safety goggles
Torque wrench
Silicone caulk
5
6
INSTALLING POP-UP DRAIN
A)
Remove pop-up plunger (A) and flange (B). Screw locknut (C) all the way down. Push
gasket (D) down. Apply silicone to underside of flange (B).
B)
Insert body into sink (from underneath). Screw flange onto body. Pivot hole (E) must face
the back of the sink.
C)
Tighten locknut (C) and gasket (D) but do not overtighten. Remove pivot ball retaining nut
(E).
D)
Slide pivot rod (F) into the eye of the pop-up plunger (A). Hand tighten retaining nut.
E)
Slide pivot rod (F) through hole in spring clip (G), then through lever strap (H) and back
through spring clip (G)
.
F)
Insert lift rod (I) down through faucet body and then into lever strap (H). Tighten screw (J).
Connect assembly to drain.
7
8
HAND TIGHTEN THE MOUNTING NUTS
From underneath the sink, hand tighten the mounting nuts. Tighten gently until snug and alternate from
side to side to seat the faucet body evenly.
Don’t over tighten
FLUSHING & AERATOR CLEANING
Remove the aerator by turning it counterclockwise. Remove the internal
parts of the aerator by pushing them out with your fingers. Remove any
debris. Turn on hot and cold water supplies. Turn faucet handles all the
way on and run water through the spout for about a minute to remove
debris. While water is running check all connections for leaks.
Reassemble the aerator and screw it back into the spout hand tight.
3
GASKET & FAUCET INSTALLATION
A)
Apply a bead of plumber’s putty or silicone caulk around the sink openings.
B)
Install the gasket over the three holes in your sink.
C)
Install faucet shanks through the holes of the sink. Centre the faucet body on the sink.
Don’t use plumber’s putty on cultured marble or other composite sinks.
Putty will discolour the sink.
2
TURN OFF THE MAIN WATER SUPPLY
Locate water supply inlets and shut off water supply valves. These are usually found under
the sink.
WARNING: READ ALL
the instructions completely before beginning.
READ ALL
warnings, care and maintenance information.
Taymor recommends calling a professional if you are uncertain about installing this product!
This product should be installed in accordance with all local and provincial plumbing and building codes.
Need Help?
Please call our toll-free Customer Support line at
(WEST) 1-800-267-4774 (EAST ) 1-800-387-7064 for additional assistance or service.
CALEDONIA 06-4670PCHL / 06-4670PSNL / 06-4670BRNL
TWO HANDLE LAVATORY FAUCET
Your installation may require new supply
lines. (Supply lines are not included.)
MAKE CONNECTIONS TO WATER LINES
Use 1/2” IPS faucet connections (1) and tighten connections with wrench. Or use the supplied plastic
coupling nuts (3) with 3/8” O.D. ball-nose risers (2), hand tighten only. Do not overtighten. Do not use
metal coupling nuts (4). Do not use plumber’s putty, pipe dope, or any other type of sealing com-
pound on water inlet or threads. Additional compound is not necessary.
2
3
1
4
