1. Adjust spring tension to match door width as indicated by chart on page 1.
2. Mount closer on door as dimension shown. Tube-end toward hinge.
If pivots are used, locate closer and shoe from CENTERLINE OF PIVOT.
(For offset pivots, increase the marked dimensions by 1/8”)
3. Place main arm on top of shaft 100° to closer body. Insert arm screw into top
of the shaft and tighten.
4. Attach shoe to frame as shown. (If more latching power is required, rotate
shoe 180°)
5. Open door and insert rod in forearm.
6. With forearm at right angle to door (90°), insert forearm set screw and tighten.
(IF HOLD OPEN ARM IS USED, THE NUT MUST BE ON TOP FOR RH DOOR AND
BOTTOM FOR LH DOOR)
GUIDELINE:
A ‘normal’ closing time from 90° open position to door closing position is 4-6
seconds, evenly divided between closing and latching speed. Use socket key
(included) to adjust the speed. To slow down closing speed, turn regulating screw
nearest shaft clockwise. To slow down latching speed, turn regulating screw
nearest latch clockwise.
BACK CHECK:
To adjust backcheck, turn the regulating screw adjacent to the door hinges
clockwise. WARNING:
Do not use backcheck function as a door stop.
COVER:
Locate top and bottom cover then push cover against the door closer. Tighten both
screws securely.
HOLD OPEN ADJUSTMENT:
(WHEN HOLD OPEN ARM IS USED)
Loosen adjusting nut, open door to desired hold open position and tighten the nut.
Do not permit door to swing beyond hold opening position.
The illustration shown below is for a LEFT HAND DOOR. For RIGHT HAND DOOR refer to template provided.
STANDARD INSTALLATION
- CLOSER MOUNTED ON DOOR ON PULL SIDE
2 HOLES FOR
#14 ALL-PURPOSE
OR 1/4-20 (M6X1.0)
MACHINE SCREWS
1-15/16”
(49 mm)
B
A
11/16” (18 mm)
11/16” (18 mm)
2-1/4” (57 mm)
1”
(25 mm)
4 HOLES FOR
#14 ALL-PURPOSE
OR 1/4-20 (M6X1.0)
MACHINE SCREWS
3”
(76 mm)
1”
(25 mm)
11-3/8”
(289 mm)
6-3/4”
(171 mm)
OPENING
“A”
“B”
TO 100°
7-5/16”
(185 mm)
11-13/16”
(300 mm)
TO 130°
6-1/4”
(159 mm)
10-13/16”
(275 mm)
PRELOAD TO 90°
COVER SCREWS
LATCH SPEED
SCREW
MAIN SPEED
SCREW
BACKCHECK
SCREW
ROD
FOREARM SCREW
MAIN ARM
ARM SCREW
The illustration shown below is for a RIGHT HAND DOOR. For LEFT HAND DOOR refer to template provided.
TOP JAMB INSTALLATION
- CLOSER MOUNTED ON TOP JAMB ON PUSH SIDE
1. Adjust spring tension to match door width as indicated by chart on page 1.
2. Mount closer on door as dimension shown. Tube-end towards hinge.
If pivots are used, locate closer and shoe from CENTERLINE OF PIVOT.
(For offset pivots, increase the marked dimensions by 1/8”)
3. Place main arm on top of shaft 100° to closer body. Insert arm screw into top
of the shaft and tighten.
4. Attach shoe to frame as shown. (If more latching power is required, rotate
shoe 180°)
5. Open door and insert rod in forearm – use rod to reveal 2-5/8” through
4-13/16”. Use Forearm Extended Rod (available as an option) to reveal 4-7/8”
to 8”.
6. With forearm at right angle to door (90°), insert forearm set screw and tighten.
(IF HOLD OPEN ARM IS USED, THE NUT MUST BE ON TOP FOR RH DOOR AND
BOTTOM FOR LH DOOR)
GUIDELINE:
A ‘normal’ closing time from 90° open position to door closing position is 4-6
seconds, evenly divided between closing and latching speed. Use socket key
(included) to adjust these speed. To slow down closing speed, turn regulating
screw nearest shaft clockwise. To slow down latching speed, turn regulating
screw nearest latch clockwise.
BACK CHECK:
To adjust backcheck, turn the regulating screw adjacent to the door hinges
clockwise. WARNING:
Do not use backcheck function as a door stop.
COVER:
Locate top and bottom cover then push cover against the door closer. Tighten both
screws securely.
HOLD OPEN ADJUSTMENT:
(WHEN HOLD OPEN ARM IS USED)
Loose adjusting nut, open door to desired hold open position and tighten the nut.
Do not permit door to swing beyond hold opening position.
INSTALLATION DIMENSIONS
OPENING
“A”
“B”
TO 100°
7-5/16”
(185 mm)
11-13/16”
(300 mm)
TO 130°
6-1/4”
(159 mm)
10-13/16”
(275 mm)
INSTALLATION DIMENSIONS
2 HOLES FOR
#14 ALL-PURPOSE
OR 1/4-20 (M6X1.0)
MACHINE SCREWS
1-15/16”
(49 mm)
B
A
11/16” (18 mm)
11/16” (18 mm)
2-1/4” (57 mm)
1”
(25 mm)
4 HOLES FOR
#14 ALL-PURPOSE
OR 1/4-20 (M6X1.0)
MACHINE SCREWS
3”
(76 mm)
1”
(25 mm)
PRELOAD TO 90°
COVER SCREWS
LATCH SPEED
SCREW
MAIN SPEED
SCREW
BACKCHECK
SCREW
ROD
FOREARM SCREW
MAIN ARM
ARM SCREW
PAGE 3
PAGE 2
2-3/4” (70 mm)
