background image

OPERATING PROCEDURES

6-5 

Models RD30/RC25 

Operating Procedures 

 6

Sanitizing (Without Post Mix Valve)

1. Fill the system.

 

Disconnect the product supply lines 

from the mix delivery container. Prepare a pail of 
approved 100 ppm sanitizing solution (examples: 

2-1/2 gal. [9.5 L] of Kay-5

®

 or 2 gal. [7.6 L] of 

Stera-Sheen

®

). Use warm water and follow the 

manufacturer’s specifications. Pour the solution into 
a clean, empty mix delivery container. Connect the 
container to the mix delivery line.

Figure 6-21

2. Place the control switch in the WASH position. Press 

the fill switch to activate the mix solenoid. The mix 
solenoid will remain open until the mix level float 
switch is satisfied. Drain sanitizer from the freezing 
cylinder and repeat this procedure until full-strength 
solution is dispensed from the mix delivery container. 
Make sure all sanitizer is removed from the fill 
system. Place the fill switch in the OFF position and 
drain any remaining solution from the freezing 
cylinder.

Figure 6-22

Important! 

The machine must 

not

 be placed in Auto 

mode until all sanitizing solution has been removed 
from the freezing cylinder and proper priming 
procedures have been completed. Failure to follow 
this instruction may result in damage to the freezing 
cylinder.

Sanitizing (With Post Mix Valve)

1. Prepare a pail of approved 100 ppm sanitizing 

solution (examples: 2-1/2 gal. [9.5 L] of Kay-5

®

 or 2 

gal. [7.6 L] of Stera-Sheen

®

). Use warm water and 

follow the manufacturer’s specifications. Pour the 
solution into a clean, empty mix delivery system 
container.

Figure 6-23

2. Place the control switch in the WASH position. Place 

the fill switch in the on position. To prime the fill valve, 
press and hold the area marked PUSH on the front of 
the post mix valve (prime button). After 10 seconds, 
release the valve, and the sanitizing solution will 
continue to flow until the mix float is satisfied or until 
the fill switch is turned to the OFF position.

Figure 6-24

Содержание RD30







































Отзывы: