Taylor C819 Скачать руководство пользователя страница 7

3

Models C819 & C821

To the Operator

Section 2

To the Operator

The grill you have purchased has been carefully
engineered and manufactured to provide
dependable operation.

This grill, when properly operated and maintained,
will produce a consistent quality product. Like all
mechanical products, it will require cleaning and
maintenance. A minimum amount of care and
attention is necessary if the operating procedures in
this manual are followed closely.

This Operator's Manual should be read before
operating or performing any maintenance on your
equipment.

It is strongly recommended that all personnel
responsible for the equipment's operation and
cleaning review these procedures for proper training
and assurance that no misunderstandings exist.

In the event you should require technical assistance,
please contact your local authorized Taylor
Distributor.

Note:

Warranty is valid only if the parts are

authorized Taylor parts, purchased from an
authorized Taylor Distributor, and the required
service work is provided by an authorized Taylor
service technician. Taylor reserves the right to deny
warranty claims on equipment or parts if
non-approved parts or refrigerant were installed in
the machine, system modifications were performed
beyond factory recommendations, or it is determined
that the failure was caused by neglect or abuse.

Note: Constant research results in steady
improvements; therefore, information in this
manual is subject to change without notice.

If the crossed out wheeled bin symbol is

affixed to this product, it signifies that this product is
compliant with the EU Directive as well as other
similar legislation in effect after August 13, 2005.
Therefore, it must be collected separately after its
use is completed and cannot be disposed as
unsorted municipal waste.

The user is responsible for returning the product to
the appropriate collection facility as specified by your
local code.

For additional information regarding applicable local
laws, please contact the municipal facility and/or
local distributor.

Содержание C819


















































Отзывы: