manualshive.com logo in svg

Taylor C723, Руководство по обслуживанию, Страница: 21 / 88

Поделиться
Скачать
Taylor C723 Скачать руководство пользователя страница 21

 17

Model C723

Controls, Systems and Operations

140519

Manager's Menu

______________________________

The Manager's Menu is used to enter the operator
function displays. To access the Manager's Menu,

press the center of the CONE symbol 

 on the

control panel on the right side of the machine. The

arrow keys, the SEL key, and the CONE symbol 
will be illuminated when the ACCESS CODE screen
is displayed. (See Figure 10.)

Figure 10 

In the menu program, the arrow keys and the SEL
key will function as menu keys.

UP ARROW

 

-

 increases the value above the cursor

and is used to scroll upward in text displays.

DOWN ARROW

 

-

 decreases the value above the

cursor and is used to scroll downward in text
displays.

SEL

 

-

 advances the cursor position to the right and

is used to select menu options.

Note:  

The machine will continue operation in the

mode it was in when the menu was selected.
However, the control keys will not be illuminated and
are non-functional when the Manager's Menu is
displayed.

Entering Access Code

With the ACCESS CODE screen on the display, use
the SEL key to set the first code number in the
cursor position. When the correct number is
selected, press the SEL key to move the cursor to
the next number position. (See Figure 11.)

ENTER ACCESS CODE

8

3

0

9

__

Figure 11 

Continue to enter the proper access code numbers

(8309)

 until all four numbers are displayed and then

press the SEL key. The Manager's Menu list will
display on the screen, provided the correct access
code is entered.

If an incorrect number is entered for the access
code, the display will exit the menu program when
the SEL key is pressed. (See Figure 12.)

Figure 12 

Содержание C723

























































































Отзывы:

Нет отзывов