background image

6-10  

OPERATING PROCEDURES

Model C302 

Operating Procedures 

To disassemble the Model C302, the following items will 
be needed:
• 

 Two cleaning pails

• 

 Necessary brushes (provided with freezer)

• 

 Cleaner

• 

 Single-service towels

Draining Product from the Freezing 

Cylinders

1. Press the BEATER (- - -) key. This will allow the 

beater to operate, and CO

2

 pressure will be 

maintained to push the product from the freezing 
cylinder. Open the draw valve and drain the product 
from the machine until the CO

begins to jet.

Figure 6-38

2. When all the product has been drained from the 

freezing cylinder, close the draw valve and press the 
OFF (<- -) key. Discard this product.

Figure 6-39

3. Repeat step 1 through step 2 for the other freezing 

cylinders.

Rinsing

Note:

The following instructions are for one pair of 

freezing cylinders under an LCD. 

1. To place the left cylinder in the Rinse mode, press 

the MENU (SELECT) key. Move the cursor by 
pressing the AUTO (- ->) key until the third line 
indicates RINSE / SANITIZE.

2. Press the MENU (SELECT) key. Move the cursor 

under RINSE by pressing the OFF (<- -) key twice.

3. Pressing the MENU (SELECT) key will give you the 

option for rinsing the left freezing cylinder. Move the 
cursor under the word YES. Pressing the MENU 
(SELECT) key at this time will start the beater motor 
and deliver water and CO

2

 to the left cylinder.

4. Allow the rinse water to flow into the cylinder until it is 

approximately two thirds full. With a pail under the 
door spout, open the draw valve and drain the rinse 
water. Repeat this procedure until the rinse water 
being drawn is clear.

5. Repeat step 3 through step 4 for the right freezing 

cylinder.

Note:

There is a left and a right freezing cylinder for 

each LCD.

6. When draining is complete, press the OFF (<- -) key.

13039b

13039o

OPERATOR MENU

A B C D E F G H I

RINSE / SANITIZE

L

E

S

>

-

-

-

-

<

RINSE / SANITIZE

RINSE

SANITIZE

EXIT

- - - -

L

E

S

>

-

-

-

-

<

RINSE

LEFT

SIDE

YES

NO

- - -

L

E

S

>

-

-

-

-

<

RINSE

RIGHT SIDE

YES

NO

- - -

L

E

S

>

-

-

-

-

<

Содержание C302





















































Отзывы: