manualshive.com logo in svg

Taylor 428, Руководство оператора

Поделиться
Скачать
Taylor 428 Скачать руководство пользователя страница 30

6-10  

OPERATING PROCEDURES

Model 428

Operating Procedures 

6 

Priming the Freezing Cylinder

1. With a pail beneath the door spout, open the draw 

valve. Pour 2 gal. (7.6 L) of 

fresh

 mix into the hopper 

and allow it to flow into the freezing cylinder. This will 
force out any remaining sanitizing solution. When 
full-strength product is flowing from the door spout, 
move the draw valve to the left.

Important! 

 Failure to remove all sanitizing solution 

may result in damage to the freezing cylinder.

2. When mix has stopped bubbling down into the 

freezing cylinder, install the air/mix feed tube 
(optional) in the mix inlet hole with the hole side 
down.

Figure 6-39

3. Place the power switch in the AUTO position. When 

the machine cycles off, the product will be at serving 
viscosity. The viscosity (thickness) of the product can 
be adjusted by turning the viscosity adjustment screw 
on the upper right side under the display light. Turn 
the viscosity adjustment screw clockwise for a thicker 
product, or counterclockwise for a thinner product. 
After making an adjustment, the refrigeration system 
must cycle two or three times to accurately evaluate 
the viscosity.

Figure 6-40

4.

Self-Closing Door Only:

 Loosen the prime plug. 

When product starts to leak from the bleed port, 
tighten the prime plug. Allow product to continue 
filling the mix hopper until the upper mix-level probe 
is satisfied and the fill system shuts off.

5. Place the mix hopper cover in position. For proper 

operation, there must be a substantial amount of mix 
in the hopper. If the ADD MIX light illuminates, refill 
the mix hopper as soon as possible.

Figure 6-41

Closing Procedure

To disassemble this machine, the following items will be 
needed:

•

Two cleaning pails

•

Cleaning brushes (provided with freezer)

•

Cleaner

•

Single-service towels

13089

101694

12032

Содержание 428















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды