Taylor-Dunn E0-455-24 Скачать руководство пользователя страница 46

Страница: 46 / 134

Transaxle

Page 46

E-455

ME-455-04

AXLE SHAFT

Note: The transaxle does not have to be removed for this

procedure.

Note: The axle hub bolt has a special thread locking

compound applied to the threads. If this bolt is

removed, it must be replaced.

Note: The hub or rotor does not have to be removed but if

they are to be replaced, then it is easier to remove

them before removing the axle from the housing.

Note: If replacing the axle seal then the axle tube must be removed but the axle does not have to be removed

from the tube.

This section is one section of a complete service

manual. Before starting any procedure, read all

warnings and instructions that are located in the

Service Guidelines chapter.

WARNING

The axle retaining plate bolts have a pre-applied

thread locking compound. They are intended for one

time use only. If removed they must be replaced.

Reusing the original bolts could cause loss of brakes

resulting in severe bodily injury and/or property

damage.

WARNING

Install

1: Install in reverse order of removal

•

Lubricate the external bearing O-ring.

•

Brush a light coat of grease onto the axle

splines and where the seal rides on the axle

shaft.

•

Use new bolts for the axle retaining plate.

•

If the wheel hub was removed, install the

hub and rotor. Torque the hub bolt to the

specification listed in the table at the end of this

section.

Fill with oil to the level of the fill plug threads.

Refer to Check Oil Level procedure.

3: Set the park brake.

4: Lower the vehicle and test drive.

Remove

1: Raise the rear of the vehicle and support with

jack stands.

2: Drain the oil from the 3rd member. Refer to

Change Oil in this section.

3: Release the park brake.

4: Remove the tire and wheel assembly. Refer to

Tires and Wheels section.

5: Remove the four bolts holding the axle retaining

plate to the axle tube.

6: Remove the axle retaining plate and brake body

assembly as one unit.

7: Secure the brake body assembly, do not let it

hang by the brake hose.

8: Pull the axle out of the housing.

9: Inspect the interior of the axle tube for oil. Any oil

in the axle tube is an indication of a leaking seal.

The tube must be removed to replace the seal.

10: Inspect all bearings for roughness or play and

replace as needed.

The hub bolts have a pre-applied thread locking

compound. They are intended for one time use only. If

removed they must be replaced. Reusing the original

bolts could result in a wheel separating from the axle

and loss of brakes resulting in severe bodily injury

and/or property damage.

WARNING

Содержание E0-455-24







































































































































Результаты поиска

Содержание E0-455-24

Отзывы:

Похожие инструкции для E0-455-24

Бренды по названию

Популярные бренды

Taylor-Dunn E0-455-24, Инструкция по обслуживанию и замене запасных частей

Результаты поиска

Содержание E0-455-24

Отзывы:

Похожие инструкции для E0-455-24

Бренды по названию

Популярные бренды