Taylor-Dunn B0-200-00 Скачать руководство пользователя страница 30

Страница: 30 / 188

Front Axle

Page 30

B-200 & B-210 Models

MB-210-13

REMOVE

1: Raise the front of the vehicle and support with jack stands.

2: Remove both front wheels. Refer to Tires and Wheels section for information regarding removing the front

wheels.

3: Tie up or support the front axle so it can not fall out of the vehicle.

4: Disconnect the drag link ball joint or rod end from the steering knuckle or the steering gear pitman arm.

Note: Refer to the Replacing the Ball Joints section for information regarding the removal of the ball joints or

rod ends.

5: If equipped with front brakes, disconnect the hydraulic brake lines from the brake bodies.

6: Disconnect the front axle beam from the front springs and remove the axle from the vehicle.

Note: In some configurations the front springs and or shocks will have to be removed in order to remove the

axle beam. Refer to section Front Suspension for information regarding removing the springs and shocks.

Installation

1: Raise the front of the vehicle and support with jack stands.

2: Install the front axle in reverse order of removal.

Note: Use all new cotter pins.

Note: Refer to the Replacing the Ball Joints section for information regarding the installing the ball joints or

rod ends.

Note: Refer to Tires and Wheels section for information regarding removing the front wheels.

3: Realign the front wheels. Refer to Steering Component Service section for information regarding realigning

the front wheels.

4: If equipped with front brakes, bleed the brakes. Refer to Brake Service section for information regarding

bleeding the brakes.

5: Lower the vehicle.

6: Reconnect the main positive and negative cables at the batteries.

7: Remove the blocks from behind the wheels.

8: Release the park brake and test drive the vehicle.

This section is one section of a complete service

manual. Before starting any procedure, read all

warnings and instructions that are located in the

Service Guidelines chapter.

WARNING

Содержание B0-200-00





























































































































































































Результаты поиска

Содержание B0-200-00

Отзывы:

Похожие инструкции для B0-200-00

Бренды по названию

Популярные бренды

Taylor-Dunn B0-200-00, Инструкция по обслуживанию и замене запасных частей

Результаты поиска

Содержание B0-200-00

Отзывы:

Похожие инструкции для B0-200-00

Бренды по названию

Популярные бренды