Taylor-Dunn B0-150-00 Скачать руководство пользователя страница 76

Страница: 76 / 136

Tires & Wheels

Page 76

B0-015-00 and MX-016-00

MB-150-03

REPLACE THE TIRE (PNEUMATIC)

Note: To replace the tire, the tire/wheel assembly

must be removed from the vehicle. Refer

to Replace the Tire/Wheel section for

information on removing the tire/wheel

assembly.

Tire replacement should only be performed by personnel

trained in tire replacement.
The tire replacement procedure will be unique to the

type of replacement equipment being used. Refer to the

instructions provided with your equipment.
Always use a new valve stem when replacing a tire.

1: Remove the tire from the wheel.

2: Cut the old valve stem off of the wheel.

3: Remove the valve stem cap from the new valve

stem.

4: Lubricate the valve stem with liquid soap.

5: Install a new valve stem using a valve stem tool.

Note: The valve stem tool is available at most auto

repair shops.

6: Install the tire onto the wheel following the

instructions provided with your tire replacement

equipment.

Inflate the tire to the proper pressure and check

for leaks.

8: Install the valve stem cap.

REPAIR THE TIRE (PNEUMATIC)

Note: To properly repair a puncture, the tire

must be removed from the wheel. Refer to

Replace the Tire section for information on

removing the tire from the wheel.

It is recommended to repair a tire with a combination

vulcanized plug and internal patch.
Tire repairs should only be performed by personnel

trained in tire repair.
The tire repair procedure will be unique to the type of

repair equipment or repair components used. Refer to

the instructions provided with your equipment or repair

components.

This section is one section of a complete service

manual. Before starting any procedure, read all

warnings and instructions that are located in the

Service Guidelines chapter.

WARNING

Improper assembly or disassembly of a split rim

wheel can result if tire explosion causing severe

injury. Refer tire/wheel repair to a qualified tire

supplier.

WARNING

CHANGING TIRE/WHEEL
ASSEMBLY

Note: A spare tire, jack, or lug wrench is not

attached to the vehicle.

1: Loosen the wheel nuts (do not remove) before

raising the tire off of the ground.

2: Raise the tire to be changed off of the ground and

support with a jack stand.

3: Remove the wheel nuts and tire/wheel assembly.

4: Install the replacement tire/wheel assembly.

5: Install the wheel nuts and cross tighten to torque

specified in table.

Check the tire for proper inflation.

7: Lower the vehicle to the ground and remove the

blocks from the wheels.

8: Check wheel nuts for tightness after 100 miles.

This section is one section of a complete service

manual. Before starting any procedure, read all

warnings and instructions that are located in the

Service Guidelines chapter.

WARNING

Содержание B0-150-00









































































































































Результаты поиска

Содержание B0-150-00

Отзывы:

Похожие инструкции для B0-150-00

Бренды по названию

Популярные бренды

Taylor-Dunn B0-150-00, Инструкция по обслуживанию и замене запасных частей

Результаты поиска

Содержание B0-150-00

Отзывы:

Похожие инструкции для B0-150-00

Бренды по названию

Популярные бренды