AFTER SALES SUPPORT
1300 922 271
MODEL NUMBER: BT-SD 3.6/Li ,
10/12
8
m
5. Technical data
Motor power supply:
3.6V DC
Idling speed:
200 min
-1
Forward/Reverse:
Yes
Charge voltage for rechargeable
battery:
6 V DC
Charge current for rechargeable
battery:
300 mA
Battery charger supply voltage:
230V - 240V~50 Hz
Charging time:
max. 3-5 hours
Battery type:
Li-Ion
Weight:
0.4 kg
Sound and Vibration
Sound and vibration values were measured in
accordance with EN 60745.
L
pA
sound pressure level
62 dB(A)
K
pA
uncertainty
3 dB
L
WA
sound power level
73 dB(A)
K
WA
uncertainty
3 dB
Wear ear-muffs.
The impact of noise can cause damage to hearing.
Total vibration values (vector sum of three
directions) determined in accordance with
EN 60745.
Screwing without hammer action
Vibration emission value a
h
= 0.153 m/s
2
K uncertainty = 1.5 m/s
2
Important!
The vibration value changes according to the area of
application of the electric tool and may exceed the
specified value in exceptional circumstances.
6. Before starting the
machine
Be sure to read the following information before you
use your cordless screwdriver for the first time:
1.
Charge the battery pack with the charger
supplied.
2.
Only ever use screwdriver bits which are
suitable for the purpose and in faultless
condition.
3.
Always check for concealed electric cables
and gas and water pipes before drilling and
screwing into walls.
7. Operation
7.1 Charging the battery
The battery is protected from exhaustive
discharge. An integrated protective circuit
automatically switches off the equipment when
the battery is flat. In this case the bit chuck will
cease to turn.
Warning!
Do not press the ON/OFF switch any
more if the protective circuit has been activated.
This may damage the battery.
1.
Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Plug the battery charger (Fig.1/
Item 11) in the plug socket and connect the
charging cable (Fig.1/Item 12) to the charging
connection (Fig.1 & 3/Item 8). The charging
process starts as soon as the charging cable
is connected to the charging adapter.
2.
The charging control light (Fig.1 & 3/Item 7)
will be red to indicate that the battery pack is
being charged.
3.
The charging control light (Fig.1 & 3/Item 7 )
goes out when charging is completed.
Important!
The handle may become a little warm
during the charging process. This is normal.
If the battery pack fails to charge, please check
•
whether there is voltage at the socket-outlet
•
and check for proper contact with the
charging contacts in the battery charger.
If the battery still fails to charge please call our
After Sales Support on 1300 922 271 .
Timely recharging of the battery pack will help it
serve you well for a long time. You must recharge
the battery pack when you notice that the power
of the screwdriver drops.
Never allow the battery pack to become fully
discharged. This will cause it to develop a defect.
7.2 Forward/Reverse switch (Fig. 2)
The Forward/Reverse switch (10) above the
ON/OFF switch (9) is for setting the direction
of rotation of the cordless screwdriver and for
preventing the cordless screwdriver from being
switched on inadvertently.
You can select between forward and reverse
rotation. Change the direction of rotation only
when the equipment is at a standstill. If you fail
to observe this point, the gearing may become
damaged. When the Forward/Reverse switch (10)
is in the middle position, the ON/OFF switch (9) is
blocked.
