background image

3

TAU

 

Srl

TSG

English

DIGITAL KEYBOARD TSG

Digital keyboard with remotely programmable codes (max. 50 codes) and mod. RXDC decoding receiver.

KEYBOARD INSTALLATION 

   Remove the screw cover (fi g. 2) with a screwdriver (fi g. 1);

   after having removed the screws (fi g. 3), remove the keyboard front from the battery casing;

   connect the battery to the keyboard front as shown in fi g. 4;

   fi x the battery casing to the chosen support (use 5 mm Ø screw anchors if fi xing the keyboard to the wall 

or  3.5 mm Ø self-drilling screws  for metal or steel supports, or 3.5 mm Ø self tapping for wooden or similar 
supports), making sure that the writing is at the top (fi g. 5) so that possible condensation can drain (1 fi g. 
5);

  Once the battery casing has been fi xed to the support, fi t the keyboard front with the battery connected and 

fi x it with the 2 supplied screws (fi g. 6);

  Finally simply push the screw cover into place (fi g. 7).  

MODIFICATION OF THE MASTERCODE 

The factory setting of the mastercode is: 

1234

.

To modify it, introduce the factory code following the sequence (1234), then 
introduce the new code (4 numbers) and confi rm by repeating the new 
sequence of numbers.  

N.B.  

The new code is now memorised.
It is a good idea to note down the new Mastercode.

MEMORY RESET 

The Mastercode is required in order to begin the memory reset and creation and 
cancellation of a code.
The memory should ideally be reset before introducing your code. To do so, 
perform the following procedure:

 

 Mastercode 

 

 

 

 

 

 

 

 Mastercode 

 

 

 

 Mastercode 

 

 

.

The operation is confi rmed with a single long beep.

CREATION OF A NEW CODE (E.G. 1111 – PERSONAL CODE)
The codes must have a minimum of 2 and a maximum of 4 digits.

After the memory has been reset, proceed with the creation of a new code:

   Mastercode 

 

 

   

 

 

   

 

 

 

 

(personal code) 

 

   

 

 

 

 

(personal code) 

 

.

The operation is confi rmed with a single long beep.

TRANSMISSION OF THE CODE TO THE RECEIVER 

Before proceeding with the code transmission, make sure you are in the programming mode on the mod. RXDC 
receiver (Press the PS1 button on the receiver – once to select channel 1 of the receiver, twice for channel 2, 
three times for channel 3 and four times for channel 4 -, the red LED that corresponds to the selected channel 
will light confi rming that the programming phase is active), then proceed as follows:

 

 

 

 

(personal code) 

 

.

The red LED on the receiver switches off confi rming that the transmission has taken place.

CANCELLATION OF A CODE 

Proceed as follows to cancel a code from the keyboard:

   Mastercode 

 

 

   

 

 

   

 

 

 

 

(personal code) 

 

   

 

 

 

 

(personal code) 

 

.

The operation is confi rmed with a single long beep.
Each time a code is cancelled from the keyboard it is also advisable to cancel it from the related channel on the 
receiver so as to avoid a build-up of unused codes on the receiver (max. 64 codes per channel).

N.B.  

If the code is introduced incorrectly the keyboard emits a double beep error signal when the

 

button is pushed. Repeat the correct sequence of the set code.

Содержание TSG









Отзывы: