manualshive.com logo in svg

Tatu Marchesan RCP2 1500, Руководство оператора

Поделиться
Скачать
Tatu Marchesan RCP2 1500 Скачать руководство пользователя страница 23

21

Marchesan Implementos e Máquinas Agrícolas “TATU” S.A.

RCP² 1500

Adjustments and operations

Operations - important points

•  Before starting working, it is advisable to do a complete check on the cutter. 

Grease the universal joints, check the oil level for all the gearboxes and tighten 

nuts and bolts.

•  The tractor lower stabilizer arms must be adjusted when the rotary cutter is 

totally lifted.

•  In order to couple and to uncouple the cardan shaft, the PTO should be 

disengaged.

•  During transportation or when making any inspection in the equipment, keep 

the PTO disengaged.

•  The ideal working speed of the PTO is 

540 rpm

.

 

See the corresponding engine 

revolution rate in the tractor manual.

•  For a better performance, we recommend a cutting height of at least 

40 mm 

far from the ground.

•  In order to get a good result, the working place should be free from stubs and 

stones.

•  Put the blades into ideal operation speed before starting cutting the vegetation.

•  In a vegetation of great density we recommend using a low speed and 

maintaining the PTO speed constant at 

540 rpm.

•  When facing overloads, the clutches will start to work and the job should be 

immediately interrupted by raising the cutter.

•  It is important to maintain the 

28 mm

 distance in the springs of the clutches 

in order to compensate the adjustment of the discs and to maintain the good 

clutch operation.

•  In excessively waved soils, the cutting height adjustment should avoid that the 

blades touch the ground excessively.

•  Do not work the PTO being the blades stuck to earth, sticks and stubs. Objects 

can be tossed and cause serious wounds.

•  During work and transportation, the presence of passengers in the tractor and 

cutter is not allowed.

•  Do not change the tractor speed, because this act can result in an inefficient 

mowing with flaws. Maintain an average speed during the whole job.

•  Recommended average speed = 

4 to 6 Km/h.

Содержание RCP2 1500



































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды