background image

 

5 - Moving tracks

 

  TASCAM MD-801R/P Mk II 

 

5–3

 

The 

 

PLAY

 

 indicator above the 

 

PLAY

 

 key will 

flash, as will the 

 

E D I T

 

 indication in the display, 

to show that rehearsal mode has been entered.

In this rehearsal mode, the last 4 seconds 
(approximately) of the previous track and the 
first four seconds (approximately) of the current 
track are continuously repeated, so that you can 
audition the “join” between the tracks.

 

4

 

At this point, it is still possible to use the 

 

TRACK

 

 keys to select another track to be com-

bined. This newly-selected track will be com-
bined with the track immediately before the 
new selection.

 

5

 

Turn the 

 

SHUTTLE

 

 wheel clockwise to com-

bine the tracks. The display will show 

 

Now 

Editing

 

, followed by 

 

Complete

 

.

The track number of the first combined track (i.e. the 
track immediately before the track selected prior to 
the combine operation) is used for the combined 
track. 

The title of the second track is appended to that of the 
first track.

 

NOTES

 

Selecting the first track and attempting a com-
bine operation will result in the message 

 

TRK Illegal!

 

 being shown on the 

display—it is not possible to combine the first 
and last tracks.

Mono and stereo tracks cannot be combined.

In some cases where an MD has had many 
edit operations performed, the 

 

Cannot 

EDIT!

 

 message may appear on the dis-

play. This does not indicate a fault with the 
disc or the machine, but is a property of the 

 

MD recording system.

 

5.5 Moving tracks

 

This function allows you to edit the running order of 
the tracks, and re-place a track in a different position. 
This can also be used with the combine function (5.4, 
"Combining tracks") in order to combine non-contig-
uous tracks.

Before a move operation, the tracks and numbers 

look like:

Following the move operation, the tracks look like:

The “gap” is closed up, and all tracks are re-num-
bered in the new sequence. A move operation can be 
carried out in the stop, play ready or play modes.

 

1

 

Use the 

 

TRACK

 

 keys, or any convenient 

method, to select the track to be moved.

 

2

 

After pressing the 

 

EDIT

 

 key, turn the 

 

DATA

 

 

dial until the display shows:

 

3

 

Turn the 

 

SHUTTLE

 

 wheel clockwise to open 

the move menu. The display will show:

The three numeric digits indicate the track num-
ber that the current track will occupy after the 
move operation.

 

4

 

Use the 

 

DATA

 

 dial to change the destination 

track number.

 

5

 

Turn the 

 

SHUTTLE

 

 wheel clockwise. The dis-

play will show 

 

Now Editing

 

, followed 

by 

 

Complete

 

All tracks will be automatically renumbered.

 

NOTE

 

You cannot move a track to itself, e.g. if you 
have selected track 1, the destination number 
cannot be 

 

001

 

. The display will show a 

 

Not Execute

 

 message if you attempt 

 

this.

 

5.6 A and B point erase operations

 

The two location points (see 4.2.6, "Playback 
between two location points") can be used for a vari-
ety of erasure purposes. Although the basic principle 

 

M O V E

?

M o v e

t o

0 0 1 ?

Track number

1

2

3

4

This track is to be moved

New track numbers

1

2

3

4

(track numbers before the move)

3

1

2

4

Содержание MD-801RmkII






























Отзывы: