Tascam DR-701D, Справочное руководство

Страница: 29 / 46

TASCAM DR-701D
29
4 – Recording
Setting the power off generator function
You can set whether or not the time code generator continues
to run if the power is turned off while the time code generator is
running.
1. On the
TIME CODE
page, select the
POWER OFF GEN
item. (see “Menu operation procedures” on page 12)
2. Set whether or not the generator runs when the power is off.
Option Meaning
ON
(default)
Set the time code generator to continue
running if the unit is turned off while it is
running.
OFF
Set the time code generator to stop
running if the unit is turned off while it is
running.
NOTE
•
This setting is only valid when the time code source is
LTC
.
•
Since time code will continue to advance when the power
generator function is
ON
, the time code generator will start
at the time corresponding to when the unit is turned on
again.
For this reason, capturing time code again and other opera-
tions are not necessary. However, this function interpolates
based on the built-in clock, so a small error could occur in
the restarted time code value when the unit is turned on
again. The built-in clock, though, is constantly calibrated
using a high-precision TCXO, so its error is less than 2 ppm.
3. When finished, press the MENU button to return to the
Home Screen.
OFF
LTC
- -:- - 11:00 12:00 - -:- - 00:00 15:00 16:00 - -:- - 11:00 12:00 - -:- - 00:00 15:00 16:00
ON
- -:- - 11:00 12:00 15:00 16:00 14:00 13:00
CAPTURE CAPTURE
POWER OFF
T/C GEN MODE POWER OFF GEN
Time
Master Timecode
10:00 11:00 12:00 13:00 14:00 15:00 16:00
10:00 11:00 12:00 13:00 14:00 15:00 16:00
OFF
LTC
- -:- - 11:00 12:00 - -:- - 00:00 15:00 16:00 - -:- - 11:00 12:00 - -:- - 00:00 15:00 16:00
ON
POWER ON POWER ON
- -:- - 11:00 12:00 15:00 16:00 14:00 13:00
CAPTURE CAPTURE
POWER OFF
T/C GEN MODE POWER OFF GEN
Time
Master Timecode
10:00 11:00 12:00 13:00 14:00 15:00 16:00
POWER ON POWER ON
OFF
LTC
- -:- - 11:00 12:00 - -:- - 00:00 15:00 16:00 11:00 10:00 00:00 10:00 11:00
ON
11:00 10:00 10:00 11:00 12:00 11:00
CAPTURE CAPTURE
10:00 11:00
10:00
10:00 11:00 10:00 11:00 - -:- - 10:00 11:00
8
Example 1: master time code is continuous
8
Example 2: master time code is not continuous
CAPTURE
Master time code is input through this unit's time code input
connector and recognized by the unit.
Checking the time code counter
On the
TIME CODE
page, the time code generator time is
shown below the
POWER OFF GEN
item (in hours, minutes,
seconds and frames).
Outputting this unit's audio as the
HDMI output audio
Outputting the audio of each input channel
from the HDMI output
You can replace the HDMI output audio with this unit's input
audio. HDMI audio has 8 channels. You can replace 2 channels at
a time with this unit's input audio.
1. On the
HDMI AUDIO ASSIGN
page, select the
SEL
item.(see “Menu operation procedures” on page 12)
2. Select two input channels and set which HDMI audio
channels they will replace.
Options:
OFF
(default),
1-2
,
3-4
,
5-6
,
7-8
3. When finished, press the MENU button to return to the
Home Screen.
Outputting the MIX audio from the HDMI
output
1. On the
HDMI AUDIO ASSIGN
page, select the
MIX
item.(see “Menu operation procedures” on page 12)
2. Set which HDMI audio channels the MIX audio will replace.
Options:
OFF
,
1-2
(default),
3-4
,
5-6
,
7-8
3. When finished, press the MENU button to return to the
Home Screen.
NOTE
•
When set to
OFF
, HDMI input audio will be output as is.
•
Settings cannot overlap.