background image

 

 

 

  TAROT ZYX-S2 Three-axis Gyro User Manual

 

TAROT  ZYX-S2  is  the  newly  developed  precision  three-axis  gyro,  using  new  MEMS  angular  rate 

sensor  and  32-bit  microprocessor,  new  control  algorithms  and  computer  setup  software,  greatly 

enhance the spin stability , vibration resistance and flight performance. Suitable for all 200-800 size 

fuel or electric helicopters. Built-in supply voltage detection function, to ensure flight safety. Providing 

free firmware upgrade. Setup process is very easy, the whole process only takes 3 minutes.   

1. Specification 

Dimensions: 37.2mm*25.2mm*13mm 

Weight: 9.8g   

Operating voltage: DC 3.5V-9V 

Operating current drain: 40mA 

Operating temperature:-15

~65

 

Maximal angular rate: 2000 degrees/sec 

Tail servo compatibility: 1.52ms analog servo, 1.52ms digital servo, 760us digital servo, 960us digital 

servo 

Swash plate servo compatibility: 1.52ms analog servo, 1.52ms digital servo 

Receiver  compatibility:  Conventional  receiver,  S-BUS,  DSMJ,  DSM2,  DSMX

will  support  more  by 

firmware upgrade

 

Supporting firmware upgrade 

Supporting Multi-Blade Rotor Head 

2. Connections 

Conventional receiver: 

 

 

S-BUS receiver(Using standard receiver cable)

 

 

Содержание ZYX-S2








Отзывы: