Tar River BPD-680 Скачать руководство пользователя страница 19

Страница: 19 / 36

BPD

680/750 Post Hole Driver

Service - Drive Unit

Disassembly

Note: Refer to

“

Auger System Drive Unit

”

diagram on page 30 for reference numbers.

Remove 12, (#17) socket head cap screws and 12 (#16) washers from cover (#14).

Lift the cover (#14) off the assembly. Item (#13) thrust washer, usually remains with the cover.

Lift (#12) sun gear from (#11) secondary carrier assembly.

Remove (#11) secondary carrier assembly from (#10) ring gear.

Remove (#10) from (#6) hub.

One tab of (#8) lock washer will be engaged in a slot of (#9) bearing nut. Bend the tab back to release (#8)

lock washer. Remove (#9) bearing nut, (#8), and (#7) thrust washer.

Take care to not damage the (#1) shaft splines and threads. Note: the (#3) bearing cone is designed with a

slip fit for (#1) shaft.

Remove (#2) seal and (#3) bearing cones from (#6) hub. Inspect (#4) bearing cups in (#6) hub. It is not

necessary to remove these parts unless replacing.

Assembly

Note: Refer to

“

Auger System Drive Unit

”

diagram on page 30 for reference numbers.

Press new (#4) bearing cups in each side of (#6) hub. It is recommended to replace (#4) bearing cups and

(#3) bearing cones in sets.

Assemble (#3) bearing cone into (#4) bearing cup at the seal end of (#6) hub and press a new (#2) seal into

(#6) hub.

Lubricate (#2) shaft oil seal and lower (#6) hub onto (#1) output shaft. Be sure to keep (#6) hub centered to

prevent damage to the oil seal. Note: Heavy duty oil seals have no lubricant on (#2) seal, (#1) output shaft

or (#6) hub.

Assemble (#3) inner bearing cone over (#1) output shaft. Place (#3) bearing cone over the output shaft

bearing journal. Press (#3) bearing cone down until the rollers are just touching (#4) bearing cup. Caution:

Avoid pressing (#3) bearing cone too far.

Note:

A special locknut wrench (PN 613A) is required for the removal of the bearing locknut. Contact

Auburn Gear to purchase this and other service tools.

Содержание BPD-680





































Результаты поиска

Содержание BPD-680

Отзывы:

Похожие инструкции для BPD-680

Бренды по названию

Популярные бренды

Tar River BPD-680, Руководство оператора

Результаты поиска

Содержание BPD-680

Отзывы:

Похожие инструкции для BPD-680

Бренды по названию

Популярные бренды