Di8DC
Tannoy United Kingdom
Tannoy North America
Tannoy Deutschland
Tannoy France
T: 00 44 (0) 1236 420199
T: 00 1 (519) 745 1158
T: 00 49 (180) 1111 881
T: 00 33 (0)1 7036 7473
E: [email protected]
E: [email protected]
E: [email protected]
E: [email protected]
Tannoy adopts a policy of continuous improvement and product specification is subject to change
Di8 DC data file // issue 1.06 // 15.01.08
The weather resistant, full bandwidth surface mount speaker system shall consist of a 200mm (8.00") full range, point source Dual Concentric™ transducer
mounted in an optimally tuned vented, injection moulded high impact polystyrene (HIPS) enclosure, rated IP64 to EN60529 (IEC529). The protective grille
shall be constructed from steel with a weather resistant coating.
Performance of the Di8 DCt surface mount speaker shall meet or exceed the following criteria: The system shall have a conical coverage pattern of
90 degrees (-6dB). Frequency response measured on axis shall be 53Hz - 35kHz (-10dB from rated sensitivity, average over stated bandwidth. Measured at
1 metre in an anechoic chamber) with no equalisation. Sensitivity shall be 91dB (1W = 2.83V for 8 Ohms). Long term power handling capacity as defined in
EIA-426B test shall be 90W, recommended amplifier power 180W. The nominal system impedance shall be 8 Ohms (in low impedance setting).
The Di8 DCt speaker system shall be equipped with a 60W high performance line transformer for use in 70.7 or 100 Volt distributed audio systems with
60W / 30W / 15W / 7.5W* Watt, OFF and Low Impedance taps available. An easily accessible rotary switch located under the rubber trim on the bottom of
the cabinet shall be available for selecting transformer and low impedance settings.
A termination recess shall be integrated with the rear panel, a removable Euroblock type locking connector with screw terminals for secure wire termination
with "loop through" facility shall be provided. A yoke mounting bracket shall be included with the speaker system and additional security shall be provided by
a tie back point.
The dimensions shall not exceed 404.3 x 260 x 260.3mm (15.92 x 10.24 x 10.25”).
The surface mount speaker system shall be the.....Di8 DCt.
*70 Volt only
Architectural specifications Di8 DCt
The weather resistant, full bandwidth surface mount speaker system shall consist of a 200mm (8.00") full range, point source Dual Concentric™ transducer
mounted in an optimally tuned vented, injection moulded high impact polystyrene (HIPS) enclosure rated IP64 to EN60529 (IEC529). The protective grille
shall be constructed from steel with a weather resistant coating.
Performance of the Di8 DC surface mount speaker shall meet or exceed the following criteria: The system shall have a conical coverage pattern of
90 degrees (-6dB). Frequency response measured on axis shall be 53Hz - 35kHz (-10dB from rated sensitivity, average over stated bandwidth. Measured at
1 metre in an anechoic chamber) with no equalisation. Sensitivity shall be 91dB (1W = 2.83V for 8 Ohms). Long term power handling capacity as defined in
EIA-426B test shall be 90W, recommended amplifier power 180W. The nominal system impedance shall be 8 Ohms (in low impedance setting).
A termination recess shall be integrated with the rear panel, a removable Euroblock type locking connector with screw terminals for secure wire termination
with "loop through" facility shall be provided. A yoke mounting bracket shall be included with the speaker system and additional security shall be provided by
a tie back point.
The dimensions shall not exceed 404.3 x 260 x 260.3mm (15.92 x 10.24 x 10.25”).
The surface mount speaker system shall be the.....Di8 DC.
Architectural specifications Di8 DC
