Tannoy CMS501 Скачать руководство пользователя страница 4

DO NOT OVERTIGHTEN!

6

6.1 MECHANICAL INSTALLATION GUIDE FOR SUSPENDED CEILINGS

Slide the tile panel back into the suspended ceiling.  The tile bridge ends will catch over
the railings, supporting the weight of the speaker.

5

Slide the speaker assembly through the hole and turn the screws on the front of the
speaker to extend the mounting wings.  Tighten the screws until a firm grip is achieved.

If using a power driver, Tannoy recommends a torque setting of 1.5Nm.

4

Place the C-ring and tile-bridge on top of the ceiling panel, aligning the C-ring over the
hole, and screw the C-ring to the tile bridge using the fixings provided.

3

Cut out the hole in the ceiling tile using a hole saw or pad saw.

2

Remove the ceiling tile from its frame and place it on a flat surface.  Mark the
cut-out area on the ceiling tile by tracing around the template provided.

1

Go to section 7 for instructions on wiring and set-up.

6.2 MECHANICAL INSTALLATION GUIDE FOR SHEET-ROCK (PLASTER BOARD) CEILINGS

Slide the speaker assembly through the hole and turn the screws to extend the mounting
wings.  Tighten the screws until a firm grip is achieved.

If using a power driver, Tannoy recommends a torque setting of 1.5Nm.

4

DO NOT OVERTIGHTEN!

Go to section 7 for wiring and set-up instructions then return to point 4 below.

3

Cut out the hole in the ceiling using a hole saw or pad saw, then slide the
C-ring into the ceiling, aligning it over the cut-out hole).

2

Mark the cut-out area on the ceiling by tracing around the template provided.

1

7

Insert grille by pushing it onto the speaker.

5

CMS

Содержание CMS501











Отзывы: