TANDBERG Media Processing System MPS 800 Скачать руководство пользователя страница 76

Страница: 76 / 179

D 13373.08
NOVEMBER 2007

MPS

Table of

Contents

TANDBERG

MPS

ADMINISTRATOR GUIDE

The System Status gives an overview of the status for the

boards and cards installed on the MPS. The information will
reflect a fully equipped MPS and may differ from the MPS
delivered.

We recommend that you check the
TANDBERG web site regularly for updated
versions of this manual:

http://www.tandberg.com/support/
documentation.php

System Status

MPS 200

MPS 800

Introduction

Quick

Setup

Using

the MPS

System

Configuration

Installation

Gateway

Configuration

MCU

Configuration

Technical

Descriptions

Appendices

Main

System

Status

Содержание Media Processing System MPS 800




















































































































































































Результаты поиска

Содержание Media Processing System MPS 800

Отзывы:

Похожие инструкции для Media Processing System MPS 800

Бренды по названию

Популярные бренды

TANDBERG Media Processing System MPS 800, Руководство администратора

Результаты поиска

Содержание Media Processing System MPS 800

Отзывы:

Похожие инструкции для Media Processing System MPS 800

Бренды по названию

Популярные бренды