TANDBERG Media Processing System MPS 800 Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 179

background image

D 13373.08
NOVEMBER 2007

MPS

TANDBERG

MPS

ADMINISTRATOR GUIDE

Introduction

Disclaimer

The information in this document is furnished for informational pur-
poses only, is subject to change without prior notice, and should
not be construed as a commitment by TANDBERG.
The information in this document is believed to be accurate and
reliable; however TANDBERG assumes no responsibility or liability
for any errors or inaccuracies that may appear in this document,
nor for any infringements of patents or other rights of third parties
resulting from its use. No license is granted under any patents or
patent rights of TANDBERG.

This document was written by the Research and Development
Department of TANDBERG, Norway. We are committed to maintain
a high level of quality in all our documentation. Towards this effort,
we welcome you to Contact us with comments and suggestions
regarding the content and structure of this document.

Patent information

The products described in this manual are covered by one or more
of the following patents:
US6,584,077

US5,838,664

US5,600,646

US5,768,263

US5,991,277

US7,034,860

US7.283.588

EP01953201

GB1338127

Other patents pending.

License Agreement

All rights reserved. This document contains information that is
proprietary to TANDBERG. No part of this publication may be repro-
duced, stored in a retrieval system, or transmitted, in any form, or by
any means, electronically, mechanically, by photocopying, or other-
wise, without the prior written permission of TANDBERG. Nationally
and internationally recognized trademarks and trade names are the
property of their respective holders and are hereby acknowledged.

Trademark and Copyright

Copyright © 2005–2007 TANDBERG. All rights reserved. TANDBERG
is a registered trademark of TANDBERG ASA and/or its subsidiaries
in the United States and/or other countries.

Disclaimer, Patent Info, License Agreement, Trademark & Copyright

7

Quick

Setup

Using

the MPS

System

Status

System

Configuration

Installation

Gateway

Configuration

MCU

Configuration

Technical

Descriptions

Appendices

Main

Introduction

«
...
5
6
7
8
9
...
»

Содержание Media Processing System MPS 800




















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Media Processing System MPS 800

Бренд: JBL Страницы: 8

Бренд: Roger Страницы: 2

Бренд: Purelogic Страницы: 60

Бренд: Discount Car Stereo Страницы: 6

Бренд: jWIN Страницы: 13

Бренд: Oak Telecom Страницы: 43

Бренд: GROM Audio Страницы: 16

Бренд: Powrmatic Страницы: 36

Colorado RCR 127

Бренд: Blaupunkt Страницы: 23

Бренд: Grundig Страницы: 85

Бренд: Trevi Страницы: 24

Talk-N-Trace TM-110

Бренд: JDS Uniphase Страницы: 20

Бренд: DriSteem Страницы: 4

Бренд: Teufel Страницы: 24

Бренд: ELBE Страницы: 19

Бренд: AMX Страницы: 58

Бренд: Samsung Страницы: 15

Бренд: Samsung Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды